I had a few of the same parts left and not sure about where they go. The biggest black piece is the Winter/ summer baffle, goes in the air filter cover
Sent from my Moto G (4) using Tapatalk
FarmerTec Huztl MS660 Updated Build Kit - Build Thread
Help Support Arborist Forum:
Sent from my Moto G (4) using Tapatalk
William Prophett
ArboristSite Operative
You're gonna hate this... The bolt and the "unknown" item #2 are gonna suck for you. That is the anti vibe mount that goes toward the rear flywheel side of the bottom of the case "on the inside". You are gonna have to pull the tank off to unstall it. Sorry for the bad luck. It is important because if you look underneath and put pressure on the handle you will see that there will be a ton of movement toward where that mount goes... I'll see if I can pull up the parts diagram to show you where it goes.
William Prophett
ArboristSite Operative
Thanks guys - Yea that bit is gonna suck a bit but that is learning for you. I wont forget it ever again 
I think one of the o-rings go in the chain adjuster, not sure why it needs it.
https://www.diyspareparts.com/parts/stihl/diagrams/ms660-magnum/f9e404cc-012c-4715-8264/
number 14
Not sure where the other goes.
I think one of the o-rings go in the chain adjuster, not sure why it needs it.
https://www.diyspareparts.com/parts/stihl/diagrams/ms660-magnum/f9e404cc-012c-4715-8264/
number 14
Not sure where the other goes.
William Prophett
ArboristSite Operative
The oring takes the "slop" out of the main worm gear. There is usually an extra one, so you may be ok. If it isn't installed, the main gear will be very loose and rack side to side and really bind up.Thanks guys - Yea that bit is gonna suck a bit but that is learning for you. I wont forget it ever again
I think one of the o-rings go in the chain adjuster, not sure why it needs it.
https://www.diyspareparts.com/parts/stihl/diagrams/ms660-magnum/f9e404cc-012c-4715-8264/
number 14
Not sure where the other goes.
MG porting
ArboristSite Guru
I had three of these parts left, the small o ring, a grommet and what your calling a throttle boot.
I would love to know where they all go
Sent from my Moto G (4) using Tapatalk
They are extras. Huztl sells a bag with all rubber parts used on the saw. They include that bag.
Example: the handle comes complete so any piece of rubber, like the throttle boot is already installed, so you wind up with an extra one in the bag. The early bags had a fuel hose too, because one was installed in handle. That holds true in the chain adjuster assembly, it comes complete in a bag, so the O-Ring in the rubber bag is extra and so on and on and on.
Now if you want to know where the extras go look on the saw and match them up. They just started providing the shutters.
My adjuster didn't have an o ring in the bag, it was in a bag with the other rubber parts. The extra one is a lot smaller. I didn't see one on the handle assembly like it. I don't know what it goes to.
Sent from my Moto G (4) using Tapatalk
that is the way it works, if you have parts that dont line up, then they had a bad day when your bags were being filled. as an example for 1.5 years they provided a 440 brake spring in the 660 kit, no 660 spring. dont try to make sense of it. just make a mental note and share with everybody what your experience was so we can keep up and try to make sense of it.
so what parts can you not sort out?
Mainly the small o ring and the other wire grommet. I only used one.
Sent from my Moto G (4) using Tapatalk
MG porting
ArboristSite Guru
The other wire grommet was to be used where the coil wires go through the case or you could use it where the coil wires go through the handle the other O-ring most likely for a smaller saw.
Bedford T you cheater!
This should have been covered in my videos
chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy
I put one there. I didn't see a place for the other one.This should have been covered in my videos
chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy
Sent from my Moto G (4) using Tapatalk
Show a photo. Otherwise it's the wrong part in your bag or an extra. Am I not being clear? Seems like we are going round and round. Show us. This is how this works.
chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy
Hey guys got my saw all together. Runs well. Thanks.
I think the small o-ring might be for the air filter. It fits that size thread really well and there is not much else to stop air getting in there.
Or am I wrong...
I think the small o-ring might be for the air filter. It fits that size thread really well and there is not much else to stop air getting in there.
Or am I wrong...
Canyon Angler
Addicted to ArboristSite
Holy cow, Goldredgergold, you outdid yourself with that 070.
Ok, it's mostly the same parts as William Prophet already posted.
Sent from my Moto G (4) using Tapatalk
