FarmerTec Huztl MS660 Updated Build Kit - Build Thread

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Hi Guys

Just finished putting together my Farmertec MS660 and I have a few parts over. Some are/seem to be spares, others I am not sure on.
View attachment 658421

Any help gratefully received.

PS my brake band came with a pin. Also thanks for all the videos chainsaw kit guy.
I had a few of the same parts left and not sure about where they go. The biggest black piece is the Winter/ summer baffle, goes in the air filter cover

Sent from my Moto G (4) using Tapatalk
 
Hi Guys

Just finished putting together my Farmertec MS660 and I have a few parts over. Some are/seem to be spares, others I am not sure on.
View attachment 658421

Any help gratefully received.

PS my brake band came with a pin. Also thanks for all the videos chainsaw kit guy.
You're gonna hate this... The bolt and the "unknown" item #2 are gonna suck for you. That is the anti vibe mount that goes toward the rear flywheel side of the bottom of the case "on the inside". You are gonna have to pull the tank off to unstall it. Sorry for the bad luck. It is important because if you look underneath and put pressure on the handle you will see that there will be a ton of movement toward where that mount goes... I'll see if I can pull up the parts diagram to show you where it goes.
 
Thanks guys - Yea that bit is gonna suck a bit but that is learning for you. I wont forget it ever again :)

I think one of the o-rings go in the chain adjuster, not sure why it needs it.

https://www.diyspareparts.com/parts/stihl/diagrams/ms660-magnum/f9e404cc-012c-4715-8264/
number 14

Not sure where the other goes.
The oring takes the "slop" out of the main worm gear. There is usually an extra one, so you may be ok. If it isn't installed, the main gear will be very loose and rack side to side and really bind up.
 
I had a few of the same parts left and not sure about where they go. The biggest black piece is the Winter/ summer baffle, goes in the air filter cover

Sent from my Moto G (4) using Tapatalk
I had three of these parts left, the small o ring, a grommet and what your calling a throttle boot.
I would love to know where they all go

Sent from my Moto G (4) using Tapatalk
 
I had three of these parts left, the small o ring, a grommet and what your calling a throttle boot.
I would love to know where they all go

Sent from my Moto G (4) using Tapatalk
They are extras. Huztl sells a bag with all rubber parts used on the saw. They include that bag.

Example: the handle comes complete so any piece of rubber, like the throttle boot is already installed, so you wind up with an extra one in the bag. The early bags had a fuel hose too, because one was installed in handle. That holds true in the chain adjuster assembly, it comes complete in a bag, so the O-Ring in the rubber bag is extra and so on and on and on.

Now if you want to know where the extras go look on the saw and match them up. They just started providing the shutters.
 
They are extras. Huztl sells a bag with all rubber parts used on the saw. They include that bag.

Example: the handle comes complete so any piece of rubber, like the throttle boot is already installed, so you wind up with an extra one in the bag. The early bags had a fuel hose too, because one was installed in handle. That holds true in the chain adjuster assembly, it comes complete in a bag, so the O-Ring in the rubber bag is extra and so on and on and on.

Now if you want to know where the extras go look on the saw and match them up. They just started providing the shutters.
My adjuster didn't have an o ring in the bag, it was in a bag with the other rubber parts. The extra one is a lot smaller. I didn't see one on the handle assembly like it. I don't know what it goes to.

Sent from my Moto G (4) using Tapatalk
 
My adjuster didn't have an o ring in the bag, it was in a bag with the other rubber parts. The extra one is a lot smaller. I didn't see one on the handle assembly like it. I don't know what it goes to. Sent from my Moto G (4) using Tapatalk

that is the way it works, if you have parts that dont line up, then they had a bad day when your bags were being filled. as an example for 1.5 years they provided a 440 brake spring in the 660 kit, no 660 spring. dont try to make sense of it. just make a mental note and share with everybody what your experience was so we can keep up and try to make sense of it.

so what parts can you not sort out?
 
that is the way it works, if you have parts that dont line up, then they had a bad day when your bags were being filled. as an example for 1.5 years they provided a 440 brake spring in the 660 kit, no 660 spring. dont try to make sense of it. just make a mental note and share with everybody what your experience was so we can keep up and try to make sense of it.

so what parts can you not sort out?
Mainly the small o ring and the other wire grommet. I only used one.

Sent from my Moto G (4) using Tapatalk
 
Mainly the small o ring and the other wire grommet. I only used one.

Sent from my Moto G (4) using Tapatalk
The other wire grommet was to be used where the coil wires go through the case or you could use it where the coil wires go through the handle the other O-ring most likely for a smaller saw.
let me share this tip for keeping your saw cleaner. it makes a big difference.

View attachment 658539
Bedford T you cheater! :laugh:
 
Mainly the small o ring and the other wire grommet. I only used one.

Sent from my Moto G (4) using Tapatalk
This should have been covered in my videos
953ee8c851f97b0dab11df27158db98e.jpg


chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy
 
Hey guys got my saw all together. Runs well. Thanks.

I think the small o-ring might be for the air filter. It fits that size thread really well and there is not much else to stop air getting in there.

Or am I wrong...
 

Latest posts

Back
Top