I got the model 5000 (?) today.The cheapo kept the spark plug.I found a plug here that works in the saw & is correct.I got it to fire on a prime,so I fueled the saw up & pulled it over only a few times & ended up with the rope in my hand,all 20 in.of it.I rewound the pulley with fresh new rope & tensioned it.I got it ready to put back on the saw in the a.m.I think the fuel tank has a leak,go figure.
Partner Chainsaw Thread
- Thread starter Arrowhead
- Start date
Help Support Arborist Forum:
Hi everyone, is there a way to distinguish a P55 from a P70 if there are no writings or logos on the cover?
Is there a way by looking at the serial number engraved in the crankcase?
Many thanks to those who will answer me
Is there a way by looking at the serial number engraved in the crankcase?
Many thanks to those who will answer me
Piotr Pakuła
ArboristSite Guru
The diameter of the cylinder, although after the serial number, can also be tried. Swedes ;-) has a list no.
I got the recoil put back together with what I believe to be the proper amount of rope.I put it back on the saw & it locked up on me.I took it back off & gave it a pull & it started working again.I think I've got an under-sized rope on it.
I put some fuel in the tank again & got it to run briefly.I went to change the fuel filter,but was impossible to do so due to some PO not putting a long enough fuel line in.The filter was way in under the carb.I went to disconnect the fuel line & it broke due to the PO using erthanol fuel,it hardened the line & made it brittle.I'll most likely have to pull the carb for a rebuild too.Here are some pics.Maybe someone can identify the model,or confirm it to be a 5000.
I put some fuel in the tank again & got it to run briefly.I went to change the fuel filter,but was impossible to do so due to some PO not putting a long enough fuel line in.The filter was way in under the carb.I went to disconnect the fuel line & it broke due to the PO using erthanol fuel,it hardened the line & made it brittle.I'll most likely have to pull the carb for a rebuild too.Here are some pics.Maybe someone can identify the model,or confirm it to be a 5000.
Attachments
Piotr Pakuła
ArboristSite Guru
It looks more like R16, what is the serial number? Go back to the guide assembly number I gave you, the numbers are older than the saw ;-)
jonsered fan
ArboristSite Lurker
Yes,yes !
The guide bar mounts are non-existent.You're telling me this saw is from the 1960's?What spark plug does it use,it came without a plug.Acres' site just says Bosch.
Piotr Pakuła
ArboristSite Guru
| Bosch WS5E lub Champion CJ6 Read a bit of history, I have posted photos of the guide assembly and their markings / the manufacturer of the saw does not exist anymore ;-) |
The mfr.of most of the saws on these stickies no longer exists.Partner,Pioneer,Poulan,McCullock,Homelite,Olympik,Jonsered,Remington,Sachs Dolmar,& many more are no longer aroundThe first 4 mentioned above were snatched up by Husqvarna Corp.
Piotr Pakuła
ArboristSite Guru
I wrote this only because the guides suitable for this model do not exist either. You have to look for a used or remodel, it would be ideal to find a storage chair I was successful, although the oil hole needs a second
I pulled the carb & rebuilt it & put a new fuel line & filter in.In the process of doing that the throttle linkage fell out & so did the choke linkage.I was able to put the choke linkage back on,but the throttle linkage I can't get hooked back on the trigger.Is there some way to look in there to see how to hook it back on?
Piotr Pakuła
ArboristSite Guru
Do you want a picture?
Yes,if it'll help.
Thank you Piotr, unfortunately I have to attempt a remote recognition, I cannot remove the cylinder ...
Swedes is a member of this forum?
I'm sorry but I don't know the forum well ...
Can you post a link to his profile or to his post about serial numbers?
Many thanx!
Piotr Pakuła
ArboristSite Guru
That was it?
Attachments
Piotr Pakuła
ArboristSite Guru
You can measure the cylinder when you unscrew the silencer and you have the serial number next to the spurThank you Piotr, unfortunately I have to attempt a remote recognition, I cannot remove the cylinder ...
Swedes is a member of this forum?
I'm sorry but I don't know the forum well ...
Can you post a link to his profile or to his post about serial numbers?
Many thanx!
Piotr Pakuła
ArboristSite Guru
There will be a link to another forum "Swedes" are over Europe too little water up ;-) its name is Magnus "chainsawcollectors" search .se
********************************/phpbb3/viewtopic.php?f=357&t=24453
********************************/phpbb3/viewtopic.php?f=357&t=24453
Piotr Pakuła
ArboristSite Guru
in cipher but it went ;-) I don't know if I won't get it ;-)
No.Do you know what a throttle trigger is?
Piotr Pakuła
ArboristSite Guru
translation is not always correct and sometimes even fun
