064 / 066 / MS660 18 flywheels, 7 coils

[Mastermind]

I've been looking for a dual key flywheel that has the B (or sometimes X) and the P markings. Jon is gone to get fuel for the tractors, when he gets back I'll see if he knows where one is. I want to post a pic to show which location is for which coil.

 

[scottwv]

OK so I got ahold of a 1300 coil and tried it. back fired through the exhaust port. So I retarded flywheel approximately 5 degrees and then it would start and run. unfortunately I have other issues with the saw to iron out. My flywheel is marked x and p but only the x is keyed. So I guess I need a different flywheel, but which one?

 

[Time's Standing Stihl]

There is a dual key 1203

Sent from my SM-G900R4 using Tapatalk

 

[scottwv]

So after looking at Dave's list of flywheels, I'm guessing I need the 1122 080 1214 flywheel with dual keyways?

 

[scottwv]

ok so scratch all my previous replys. I ended up having a carb problem. Once I got that straightened out I retried the flywheel in the x position and the saw fired right up and ran fine. So I can confirm that the 1300 universal coil will work with the 1209/1214 flywheel with the single keyway.

 

[Mastermind]

I found an 064 flywheel that doesn't align with either the "B" or the "P". Weird.....

I'm gonna rebroach it to use the 1300 coil.

 

[gunnusmc03]

Can you just mill a slot ?

 

[scottwv]

I have used a jewelers flat file and filed slots before. It actually works pretty well

 

[Definitive Dave]

I found an 064 flywheel that doesn't align with either the "B" or the "P". Weird.....

I'm gonna rebroach it to use the 1300 coil.

what is the number on it?
Dave

 

[Mastermind]

what is the number on it?
Dave

1122 400 1204

 

[Mastermind]

 

[big t double]

View attachment 433684 View attachment 433685 View attachment 433686

I think i have one of those layin around too...I believe theyre keyed for the cdic coil.

 

[BuckthornBonnie]

Yupp CDIC limited coil for that single slot 1204 flywheel. Need a coil? My case half cant accept my ignition setup so i won't be needing em. I am on the lookout for a flywheel and coil that will fit the case i have.

 

[Mastermind]

I have a Minute Man Type A broach set. It's not a metric set though. I'll be ordering a 10mm insert, and a 2mm broach key. I want to be able to redo these flywheels so any of them can use a 1300 coil.

 

[big t double]

Here's my 1204 flywheel ...looks the same as masterminds.. This is a cdic only flywheel. I also have a 1203 dual key and a 1201 single key to compare too. 1122 ignitions...yayyy!

 

[fin460]

subbing in to print this thread later

 

[Definitive Dave]

I have a Minute Man Type A broach set. It's not a metric set though. I'll be ordering a 10mm insert, and a 2mm broach key. I want to be able to redo these flywheels so any of them can use a 1300 coil.

if you actually do this and don't mind a few pics, I bet it would inspire more than a few of us to fix our paperweight limited flywheels as well
Dave

 

[Mastermind]

Will do Dave.

I have to get a metric mandrel.......

 

[bplust]

What's the correct coil for a 1122 400 1209 flywheel?

Thanks in advance,

Bryan

 

[scottwv]

What's the correct coil for a 1122 400 1209 flywheel?

Thanks in advance,

Bryan

You

What's the correct coil for a 1122 400 1209 flywheel?

Thanks in advance,

Bryan

y

What's the correct coil for a 1122 400 1209 flywheel?

Thanks in advance,

Bryan

you should be able to use the 1300 universal coil