KG441c
Keith
It can be faster with some more compression and porting and ps picco but with the 325 chain and stock compression it looks to be cutting very well and reindeer was letting it self feed also.
Newest addition 241c-m
- Thread starter KG441c
- Start date
Help Support Arborist Forum:
Spectre468
ArboristSiteNoob
Thanks, Doug! These look like strong little saws!
Thanks, Keith!
Thanks, Keith!
KG441c
Keith
We were cutting 12 to 15" pine today with a stock 261 and my mm241c and the 241 was everybit as fast. Id take the 241 in that size wood anyday
Spectre468
ArboristSiteNoob
KG441c
Keith
Yea. Ditched the arrestor, opened factory opening, and added gills. Added a 7 pin sprocket kit with ps chain. Its super nice with that setup but its getting ported when I get time. I dont understand Reindeers saw though I believe he said was at .033 squish . Mine when I got it was .023 squish and about 172psi from factory
man, i wish this thread would die, every time I sign into AS, I see some update from this thread 
Makes me wanna go buy another 241c, I sure miss mine,,,, both of them,,
Makes me wanna go buy another 241c, I sure miss mine,,,, both of them,,
That's the first tank after a reset on a brand spanking new carb, and with a top end that was recently put back together. She was even stronger on the second tank.
She is not only pulling 325, she is doing it with a 17.5" B&C(70DL), with a 7 pin rim, and that ash is very hard having grown in a dry run off area. So on the one big round, I am not leaning on it. On all the others I am pushing on it fairly hard. On the last round, well triangle, which is Chestnut, I am leaning on it hard - you can see the entire saw horse shaking, and the bar fly off the wood when the cut is done. In softwoods, she would be pretty quick. She has loads of torque. I will use her a bit more and see how she does.
KG441c
Keith
It looks great Reindeer. Good rpm. Im interested to see it under a port job again
Also with semi chisel chain.
I'm not sure she needs more work. She's been getting stronger and stronger, and does the job I need her to do. I'll put up another vid in a bit.
KG441c
Keith
With a port job I believe it will be right there with the 261 but thats just me.Also with semi chisel chain.
I'm not sure she needs more work. She's been getting stronger and stronger, and does the job I need her to do. I'll put up another vid in a bit.
It IS with the 261. Fourth tank:
Yeah, she's much better than when I first put the carb in. Got her to 6 tanks today, and she got better every tank. I am very happy with this little dude right now. Tomorrow it's back to firewood duty once again:
D
Deleted member 83629
Guest
how many tanks till this saw wakes up completely if left bone stock with no mods.
Spectre468
ArboristSiteNoob
RDeer,
That looks like a cuttin' sumbitch!
That looks like a cuttin' sumbitch!
Yeah, she's smoking now. Made a huge difference putting a few tanks through her. Seems even though you do a reset, MTronic can still take a while to really tune in. If you look at the last vid, when I first grab the saw I also go and grab a hand full of throttle to test the bog since she's been idling for at least 10 seconds there. Usually that was enough for it to have a terrible bog. But as you can see, it's gone there. So she's getting better all around.
The wood I have been cutting has all been pretty tough hardwoods, and she's done really well. The wood you see in the firewood vid is all seasoned ash and rhododendron, very hard wood, and she slices right through them with that 17" bar, 325, semi chisel chain. I am very pleased now.
KG441c
Keith
I knew u needed to give that 241 a chance. Ive had an 026 and 261 but if I had to reach for one for smaller wood it would no doubt be the 241c
Mastermind
Work Saw Specialist
I do quite a lot of these saws......
I'm thinking if the price was a little lower they would get more attention. They deserve more attention.
I'm thinking if the price was a little lower they would get more attention. They deserve more attention.
KG441c
Keith
Nice! Did u make that?
