Stihl Roller Chain Catcher's

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Trigger-Time

Addicted to ArboristSite
Joined
Sep 20, 2006
Messages
4,717
Reaction score
772
Location
U.S.A. :)
I knew Stihl made two different roller chain catcher’s.
I have ask before what the difference between the two.
But never received an answer, well today I know what it is.
One is about 0.125 (1/8) longer.

a754d7fe.jpg




TT
 
Never knew that, I have several sets on my 044`s , 046 and 066`s

Pioneerguy600

I bet you have the right roller on them all.
1122 650 7700 (short roller) is listed to fit 038-066/660

The longer roller 1135 650 7700 is for 361 & 362, Stihl does not list roller
for MS261. But I think the longer roller would work better on 261.


TT
 
I bet you have the right roller on them all.
1122 650 7700 (short roller) is listed to fit 038-066/660

The longer roller 1135 650 7700 is for 361 & 362, Stihl does not list roller
for MS261. But I think the longer roller would work better on 261.


TT

Most likely, they all came as a set for each saw and only have them on the saws I listed. Most of my saws don`t have dogs on them as they are used for bucking firewood, I usually do as most others do around here, just chuck the dogs in a pile.
Pioneerguy600
 
There's an even longer roller available for the 084/088/MS-880.

As always JJ is correct :)

My 880 came with one, I looked on mediaCat. It doesn't list one
for 088/880 but does for 084 part #1124 650 7700 and is
about 3/16 longer than 1135 roller.


TT
 
So there are 2 different part numbers on the bumper spike/ dawgs pictured. Are these for inner/outer or what?

Cool info on the roller catchers. Some of these part #s are hard to cross over.

Thanks R.B.
 
i have been looking on the net for a set for my 361 but can't find it. Is it a dealer item only??
 
So there are 2 different part numbers on the bumper spike/ dawgs pictured. Are these for inner/outer or what?

Cool info on the roller catchers. Some of these part #s are hard to cross over.

Thanks R.B.

Yes they are inner and outer for MS361 or MS362 spike kit.
The kit will fit a few others saws like 034 and 036.
Some have used it on 028, 026/260 and 261 from
what I have read.

Kit comes with the 2 spikes and roller chain catcher, 1135 650 7750


TT
 
My MS362 came with the roller chain catcher since it was an R model. I have added it to my 660 and 441. I find that noodles don't catch on the roller catcher like it does on the stock catcher that came on the saw.

Steve
 
i just ordered a set with the roller for my 361 30.99 for the set.

I think you will like it!

Watch not to lose the little keeper for roller when
you open the bag. You can use a small piece of
tubing or socket to drive keeper on roller shaft.
If you don't have a set of snap ring pliers that fit.

TT
 
that could be really cool,if any off you guys would help me

There is no kit that I know of for 046.

You will have to order inner/outer spikes along with nuts & bolts and roller chain catcher


440/460 inner 1122 664 0506
460 outer 1128 664 0501
Roller chain catcher 1122 650 7700

Dealer should have on hand the 2 screws and nuts you need for outer spike.
9008 319 0960 2 Hexagon head screw M5x12
9214 320 0700 2 Lock nut M5

Check these numbers over with dealer before you order them.

Look it spend close to $40 for items listed above.


TT
 
Last edited:
Back
Top