Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
RenaisSAWnceMan

RenaisSAWnceMan

ArboristSite Operative
. AS Supporting Member.
Joined
Apr 16, 2011
Messages
342
Location
MA
Roller-nose bar(s)

Lookin' for a roller-nose bar, or two. No specific saw application in mind, presently, just have a hankerin'..... Prefer the hidden-tang type, with only the roller wheel visible. Nothing much longer than my arm, though, but short is fine too.

Not much in the way of uncommitted parts to trade. Perhaps, you'll be willing to accept fully-unbacked, fiat currency....:msp_unsure:

Thanks.

*** ROLLER nose....vintage type, not 'sprocket nose' as per current-popularity....
 
Last edited:
Tpagel

Tpagel

ArboristSite Operative
Joined
Nov 23, 2010
Messages
406
Location
Central IL
Roller bar

Lookin' for a roller-nose bar, or two. No specific saw application in mind, presently, just have a hankerin'..... Prefer the hidden-tang type, with only the roller wheel visible. Nothing much longer than my arm, though, but short is fine too.

Not much in the way of uncommitted parts to trade. Perhaps, you'll be willing to accept fully-unbacked, fiat currency....:msp_unsure:

Thanks.

I have one it is a 20" GB NOS .50 .325, I think it is for Husky small mount, maybe Stihl.....
I can check if you want when I get home.
PM me
 
djones

djones

Addicted to ArboristSite
. AS Supporting Member.
Joined
Nov 25, 2010
Messages
5,125
Location
uptown Porter Corners, NY
Lookin' for a roller-nose bar, or two. No specific saw application in mind, presently, just have a hankerin'..... Prefer the hidden-tang type, with only the roller wheel visible. Nothing much longer than my arm, though, but short is fine too.

Not much in the way of uncommitted parts to trade. Perhaps, you'll be willing to accept fully-unbacked, fiat currency....:msp_unsure:

Thanks.

I have this bar if you're interested.View attachment 184544
 
Dennis Gauge

Dennis Gauge

ArboristSite Operative
Joined
Sep 1, 2010
Messages
328
Location
Spencerport NY
At the risk of looking like a total fool...

I have a loop of usable Oregon semi-chisel chain .050 gauge, 3/8" pitch, 76 drive links.

Only problem with the chain is a few links are rusty where the tip of the bar was exposed to some moisture.

I need a loop of .058 gauge, 3/8" pitch, 76 drive links. .063 might even work because the bar is wore pretty bad.

Doesn't have to be new or pretty, but it has to be good enough to make a demonstration cut once in a while. It's for a "wall hanger" saw, just to make it complete.
 
Bowtie

Bowtie

Gearhead
Joined
Dec 16, 2006
Messages
6,658
Location
Central Kansas
034/036/MS360 PTO Crank bearing

Really need a good clutch side crank bearing (or case half with a good bearing). Mine has a broken cage and I dont have a cage that fits.

I have lots of misc. Stihl parts for 026/036/044/046/064/066 and cash.
 
Nardoo

Nardoo

Addicted to ArboristSite
Joined
Jan 13, 2010
Messages
1,672
Location
Down under
Air filter cover Dolmar/Makita

Need a cover for my Dolmar 410 like this one. Can pay $$$$

chainsaw_parts_412946_small.jpg
 
Mastermind

Mastermind

Work Saw Specialist
Joined
Nov 21, 2009
Messages
36,449
Location
Tennessee
For a Husky 55 project I'm working on. I need a air filter base, choke rod, three av bushings, a coil, and a brake flag.

I just finished turning the base of the jug .045. I'll start a thread tomorrow. :rock:
 
jimbo1490

jimbo1490

ArboristSite Guru
Joined
Aug 28, 2004
Messages
587
Location
Orlando, FL
I have a brand new Tillo 12A 880 carb and the coil. Also have a handful of the blue Husky coils for 372-390, all brand new.
Actually I have a shop full of stuff, looks like an eBay Stihl and Husky abortion.


I need a couple of coils as I'm doing a 371K conversion and also building a 385. PM me a price or a wish list.

Jimbo
 
jimbo1490

jimbo1490

ArboristSite Guru
Joined
Aug 28, 2004
Messages
587
Location
Orlando, FL
Really need a good clutch side crank bearing (or case half with a good bearing). Mine has a broken cage and I dont have a cage that fits.

I have lots of misc. Stihl parts for 026/036/044/046/064/066 and cash.

I'm 99% sure I've got a good one (100% if I'm willing to split something:msp_biggrin:)

Is this the same bearing as on the clutch side of the 028? If not I've got several 034/36 case assy's, all with good cranks and bearings.
 
Top