Search results

A lot of snowmobiles can reverse direction at a push of a button. It slows the engine then advances the timing to backfire the motor, once running backwards it works just fine.

Keep one meter that get the line split to different services. Here if you have a separate meter you will have another monthly service fee.

Looks like some of the elbows are for water pluming. If they have a split seam they will not hold up hydraulic pressure. For a couple of dollars to put the right fittings in you may save yourself a hot oil bath. The rest looks like a great use of old metal.

Hyd. valve Make sure the valve on the splitter is set up for open center hydraulics. When the valve is in neutral oil should be flowing though the valve back to the tractor. If oil can't flow back it will have to flow thought the relieve valve heating up the oil.

460 hyd valve It's been a while but I think the old farmalls and a lever to choose between one-way cylinder and two way cylinders on the rear hyd. valve. Try to get a hold of a owner manual if you can.

Blender pumps are very well marked. A different colored hose is used for blends over E10. You have to push a button that has the amount of ethanol right on it, E20, E30, E50, and E85. http://minnesota.publicradio.org/display/web/2007/11/12/ethanolanniversary/

If your the sole owner for the LLC and make all the decisions they can sue right though and still get into you pockets. Just makes more work for the lawyers.

Freedom motors Freedom motors has been claiming to be coming out with rotary power tools for a few years. They just need your money to make it happen.:dizzy: http://www.freedom-motors.com/

Test ride Take a test ride in a skid that has solid tires. Ride is quite rough, may want to think about a semi-solid tire. Something along this line. http://www.mclarenusa.com/nu-air/nu-air-semi-pneumatic-tires-for-skid-steer-loaders-and-backhoes.html

Found what you need. http://www.tamanetusa.com/pallet_net_wrap.html

net wrap You could use net wrap made for big round bales. Might cost a little more than plastic but would allow the wood to breath. These rolls are 48 inches wide but you may be able to find a similar thing in shorter sizes. http://www.ambraco.com/BaleBind.htm

"Blue Forge" wood stove Here is a link to company that has a video of there unit burning. I looking into getting one of these last fall, cost was about $8500. He also said this is not an outdoor unit, should be placed in an unattached garage. http://www.ka-lesdistributing.com/

IH hydraulics The pressure is set by the bypass valve not the pump. You should hear a wining noise when the lever is pull but nothing is moving, this is oil going though the bypass valve. You can buy a higher pressure valve from the IH backhoe tractors and just screw it in. If it is the pump...

Splitter passed, catch table failed. :jester: That thing should last years. Nice job.

Rhino liner I had the dealer put a Rhino liner in before I even seen the truck. Covers the bed rails too. In four years of use there is just a few scratches from sliding full pellets on it. Would do it again in a heartbeat. Might even do the bottom of the rocker panels in a few years if the...

That gain includes all cost. Even the food the farmer eats is in some studies. They have to include solar energy that the corn uses to come out with a negative energy balance. The efficacy of grow corn has increased dramatically in the last 20 years as well as the ethanol plants them self are...

The energy gain is 20% to 35%. It's not a cure all but a small step to better energy sources.

No water in alcohol Yes they remove all water from the grain alcohol in the US it call neat alcohol. But I wouldn't be surprised if the gasoline had more than .5% water in it. Brazil uses hydrous ethanol. They can get away with it because all gas has 22% alcohol. The higher alcohol content...

Stopping distance What happens to the stopping distance when a 1000 pounds is moved from a braking axle to a non brake axle. If you where to run into something it could be a interesting talk with the DOT.

Simple way to check by pass The simplest way to check for cylinder by pass it put a steel block by the wedge (something to keep the cylinder from bottoming out), extent the cylinder as far as you can, you should hear the oil going though your relieve valve. Take the hose off the rod end, start...