Nik's Poulan Thread

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Modifiedmark
Joined
Dec 2, 2007
Messages
19,290
Location
NW Indiana
The Dayton 4Z252 that 04titanse picked up for me last week arrived today. The saw looks to be in solid condition, it is one owner and came with the wrench and a bunch of literature in the original envelope from W.W. Grainger.

While the saw was clean (the bar plates are like new), I gave it a good cleaning. When I pulled the muffler this is what I saw:

Got it back together and it has 160# of compression. Just proves it pays to take the time to look a saw over before cranking it. Now to find a bar for it...

Nice saw! You also gave a good example of why I cringe whenever I hear someone say they found a saw thats been stitting for 100 years and the first thing they do is to gas er up and tried to start it. :msp_rolleyes:
 
cmarti

cmarti

ArboristSite Guru
Joined
Jan 3, 2009
Messages
693
Location
Ohio
I learned that with my WildThing. Did exactly what you said. Keep opening the Lo needle whlie squeezing the throttle. Was surprised as it must be 2 turns open or more.
Bob

Well i got the 42 cc strato Craftsman running. New carb,piston assembly lines and ignition module, so I am 65 $ and too many hours into a $75 saw. But learned while doing it. 2.75 turns out low and 1.75 high, made me glad I listened to you guys. I am sure the too big muff mod I did, is not helping. Would have never thought......but is is running/cutting well.
 
leecopland

leecopland

Addicted to ArboristSite
. AS Supporting Member.
Joined
Oct 30, 2011
Messages
1,419
Location
huntsville ontario
stratos muff mod

Well i got the 42 cc strato Craftsman running. New carb,piston assembly lines and ignition module, so I am 65 $ and too many hours into a $75 saw. But learned while doing it. 2.75 turns out low and 1.75 high, made me glad I listened to you guys. I am sure the too big muff mod I did, is not helping. Would have never thought......but is is running/cutting well.

I'm just putting one back together ( lean scoring by someone else). The mufflers on these are quite different than the older 42cc poulans, so any advice, photos of what you did would be welcomed.

Be safe,

Lee:rock:
 
cmarti

cmarti

ArboristSite Guru
Joined
Jan 3, 2009
Messages
693
Location
Ohio
I'm just putting one back together ( lean scoring by someone else). The mufflers on these are quite different than the older 42cc poulans, so any advice, photos of what you did would be welcomed.

Be safe,

Lee:rock:

These must be set pretty lean, and/or my buddy did not use alot of sense. This had some scoring, and the piston and cylinder had a baked on powder coat and the ring was froze. The ignition was done and flywheel grooved from riding on the contacts, as the coil anchor threads were stripped. The cracked intake was the cherry on top. I got a new ignition, intake, buffed the flywheel on a lathe, and JB weld and tapped the mounting holes.

Anyway...I removed the deflector and open the exhast slit along the bottom and curled it around to the open end of the deflector. I did not feel like opening the can to get to the diffuser, so I bent it down(needlenose pliers) to funnel exhaust straight to the deflector. Then I pryed up the deflector opening and put it back on. Even before the mod this thing needed two turns out on the low to idle. It needs close to three to accelerate on throttle. Compression is great with new ring and piston, so I am surprised I am almost double the recommended low setting of 1.5 turns. The boys here counseled me to keep going on the low adjustment.....:dunno:

Hopefully, will be a good little saw now. Good luck,

Chris
 
Last edited:
Flintknapper

Flintknapper

ArboristSite Operative
Joined
Jul 17, 2009
Messages
348
Location
Deep East Texas
Questions...?

Looks like I am going to be doing some ‘noodling’ today (not because I want to).

The firewood I cut recently is just too big for me to handle (load on trailer) and I don’t want to split it where it is….so I am going to cut the pieces in half…then load on the trailer.

I could take the tractor down there….but I think it would be more work than just cutting the wood into more manageable pieces.

firewood2640x478_zpscd24975b.jpg


I haven’t (purposely) cut wood “with the grain” very much….so anything I need to watch for?

I know it is going to tend to load the saw (as the chips/noodles will be longer)….so I am guessing I need to just let the saw do the work at its own pace?

Probably use my 4900 for this. Any need to adjust the oiler to a higher rate?

Any tips will be appreciated.

Thanks,
Flint.
 
zogger

zogger

Tree Freak
Joined
Nov 23, 2010
Messages
16,456
Location
North Georgia
Looks like I am going to be doing some ‘noodling’ today (not because I want to).

The firewood I cut recently is just too big for me to handle (load on trailer) and I don’t want to split it where it is….so I am going to cut the pieces in half…then load on the trailer.

I could take the tractor down there….but I think it would be more work than just cutting the wood into more manageable pieces.



I haven’t (purposely) cut wood “with the grain” very much….so anything I need to watch for?

I know it is going to tend to load the saw (as the chips/noodles will be longer)….so I am guessing I need to just let the saw do the work at its own pace?

Probably use my 4900 for this. Any need to adjust the oiler to a higher rate?

Any tips will be appreciated.

Thanks,
Flint.

Yes, just let it feed, use a wedge to keep the kerf open, cut at a slight angle. Lift the saw to let the noddles clear as needed.

Noodle cuts are actually easier than bucking cuts or ripping cuts. You just get long noodles, thats all.
 
rms61moparman

rms61moparman

Addicted to ArboristSite
Joined
Mar 9, 2008
Messages
8,743
Location
Franklinton, Ky.
The noodles will get shorter if you let the tip of the bar go considerably deeper than the heel.
It will help keep the clutch cover from getting so clogged up.
Personally, if I were doing that with the saws you have, I would take the bar cover off and replace it with a couple stacks of flat washers.
But I would NEVER suggest someone else doing that!


Mike
 
OhioGregg

OhioGregg

Addicted to ArboristSite
. AS Supporting Member.
Joined
Aug 25, 2008
Messages
3,977
Location
Jenera, Ohio
The noodles will get shorter if you let the tip of the bar go considerably deeper than the heel.
It will help keep the clutch cover from getting so clogged up.
Personally, if I were doing that with the saws you have, I would take the bar cover off and replace it with a couple stacks of flat washers.
But I would NEVER suggest someone else doing that!


Mike

:ices_rofl: I like that advice. I was thinking the same thing, but didn't have the guts to say it. (safety police could be lurking). I have never tried it, but I might.:msp_wink: I don't noodle cut very often. When I do, I just use my 385xp, it clears them much better. Can still plug, but not as bad as the Poulans.

:cheers:
Gregg,
 
RedneckChainsawRepair
Joined
May 11, 2012
Messages
9,402
Location
Ohio
I would take the bar cover off and replace it with a couple stacks of flat washers.
But I would NEVER suggest someone else doing that!


Mike

I had a small mount 362xp I built from scratch and hadnt found a clutch cover for once I had got to the firing up stage. Big mistake test cutting without clutch cover.
I then modded a large mount 372 cover to fit the small mount 362 till I found a oem small mount cover. :biggrin:

 
redunshee

redunshee

Addicted to ArboristSite
Joined
Oct 16, 2007
Messages
6,994
Location
Texas, but spend time in Vermont
:ices_rofl: I like that advice. I was thinking the same thing, but didn't have the guts to say it. (safety police could be lurking). I have never tried it, but I might.:msp_wink: I don't noodle cut very often. When I do, I just use my 385xp, it clears them much better. Can still plug, but not as bad as the Poulans.

:cheers:
Gregg,

With the bar and chain on will it remove the possibility of the clutch coming off?
 
Flintknapper

Flintknapper

ArboristSite Operative
Joined
Jul 17, 2009
Messages
348
Location
Deep East Texas
Done.........

Well that wasn't so bad. I am always impressed at how ‘torque-y’ this saw (and the S25) is.

Noodles5_zps71e2251e.jpg


It just never gives up.


Holding the saw parallel with the ground…made for smooth cutting (and no effort on my part), but produced a LOT of long noodles quickly.

Noodles1_zps56f67eeb.jpg


Noodles2_zps902952b1.jpg



Working the tip down into the wood and then following with the heel (as per normal bucking) was considerably faster and didn’t clog the clutch cover. The noodles were much shorter that way (almost chips) and I still got a smooth cut.

Noodles4_zps89d4c080.jpg



Done in about 30 minutes. Took the time to tune my saw (in the wood) after the first cut.

Noodles3_zpsad68379d.jpg


Even cut one smaller piece with my S25. Had a new (sharp) low profile chain on it….and it really did a good job.

My 3400 and 3800 suck….compared to the S25 and the 4900, both saws make amazing power for their size.

Anyway, I am now ‘initiated’.

Thanks for the tips guys.

Flint.
 
fossil
Joined
Jan 10, 2012
Messages
6,828
Location
Southern Ontario
Wood ID

I'm not sure where to post this but I was wondering if anyone could ID this wood.
I picked up a bit of for my fireplace wood stock. It did not split easily and I don't think there was a straight grained piece in the lot.
It has threads of bright pink, almost red color running through it. High water content. The trunk was quartered but was probably
28" in diameter. I had to noodle most of it with the 4200


 

Latest posts

Top