Christmas Giving 2015

[wde_1978]

PM me an address and I can ask at the post office what postage would run. I may be prohibitive but we'll see.

It looks like postage would be in the vicinity of $50 (OUCH!). That's more than the chains are worth.

Thanks for checking!
Yeah OUCH! to say the least!

That is what I was afraid of, 50$ shipping for 2 chains is ridiculous.
That will kinda kill any hopes to claim a gift!

Trying to figure out how/what I could contribute to this thread, will have to keep shipping in mind.

 

[Philbert]

Trying to figure out how/what I could contribute to this thread, will have to keep shipping in mind.

You can be a 'Europe Only' Santa?

Philbert

 

[wde_1978]

You can be a 'Europe Only' Santa?

Philbert

With not too many presents to deliver even if I had something of interest to gift.

Who is from Europe or close by anyway, 7sleeper , CapitaineHaddoc , Ferguson system , reindeer - anyone else?

Up to 500 gram weight package shipping to the US isn't actually too bad, I just have to figure out some gift of value higher than shipping cost.
I have something in mind, just have to check availability.

 

[clemsonfor]

Here are some chains for folks who can use them. First, a pair of unused 3/8"x0.050"x81DL loops.
View attachment 470617

Next, some chains from a collection of rental chains. They have been used for one rental, then replaced with a new chain. Most are still sharper than most of the chains I see on used saws and all have lots of life left in them.
I'm offering 4 pairs of 3/8"x0.050"x72DL lops and 5 pairs of 3/8"LoProx0.050"x57DL. Because the small loops are an odd size (certainly they are for my saws), I will shorten them to whatever DL count is needed. Here is a sample of each type:
View attachment 470618

One pair of loops per person, please. I'll cover the postage.

P.S. I still have the two pair of Caber rings, 42mm x 1.2mm. They should fit an early 025. The later 025s and MS250s have a 42.5mm piston. Check your measurements to be sure they'll fit in your refresh/rebuild. I believe these also fit the FS450 trimmer and Solo 645.

Still have the 20" loops?

 

[atpchas]

Still have the 20" loops?

One more pair left. PM me with mailing info.

Note to all: The 84DL loops and now the 72DL loops are all claimed. Several pair of 3/8LP in 57DL or shorter are still available, as are the Caber rings.

 

[pioneerguy600]

Thanks for checking!
Yeah OUCH! to say the least!

That is what I was afraid of, 50$ shipping for 2 chains is ridiculous.
That will kinda kill any hopes to claim a gift!

Trying to figure out how/what I could contribute to this thread, will have to keep shipping in mind.

You and I are sorta in the same boat, I am only a border crossing away and it would cost me $43. to ship a couple of chains to the USA, they can ship me stuff for about half that cost. Really restricts what us Canadians can send over the border.

 

[redfin]

You and I are sorta in the same boat, I am only a border crossing away and it would cost me $43. to ship a couple of chains to the USA, they can ship me stuff for about half that cost. Really restricts what us Canadians can send over the border.

Bad logistics to drive across and ship stuff for you? Serious question if you are selling saws in the lower US. Just wondering.

 

[pioneerguy600]

Bad logistics to drive across and ship stuff for you? Serious question if you are selling saws in the lower US. Just wondering.

Yes, I am about 350 miles from the border.

 

[dall]

lol 350 miles is a long ways

 

[Philbert]

Yes, I am about 350 miles from the border.

Er, 560 kilometers . . . ?

 

[pioneerguy600]

lol 350 miles is a long ways

Don`t make the trip very often!

 

[kr5258]

I have 2 new air filters for Sachs Dolmar 117 to 120 or a 6800 and a new fuel cap. I will get Pics and see if I have part #.
Anyone need these.

I need a 6800 air filter. Still available?

Just checked the IPL, P/N: 121173151

 

[pioneerguy600]

Er, 560 kilometers . . . ?

My guess was a little off, computer says 553.8 km following the Trans Canada.

 

[Philbert]

I gave you a few km allowance for rest stops, historical markers, garage sales, . . .


Philbert

 

[MnSam]

Here is a nice used Stihl HD air filter and felt wrap up for grabs. This came off my 440, surely will fit others (unknown to me).

*Claimed*

 

[mkinslow]

Well the knife is coming along nicely. Here's the sheath being wet formed to the knife. Sorry for not posting much on it last week or so just having life issues with losing a job and sick kids.

 

[Rudedog]

My guess was a little off, computer says 553.8 km following the Trans Canada.

Why can't you be like all of the other Canadians and live within 60 miles of the border. Trouble maker.

 

[redfin]

Yes, I am about 350 miles from the border.

Gotcha. When you wrote "just a boarder crossing away" I expected a bit closer distance.

 

[mkinslow]

O and here's another surprise. And I gotta give props to homelite410 for letting me use his idea. Thanks bud. This one is going out to a lucky winner as lottery style. If you will actually use the knife post your name in the thread as you would in homelite410's lottery and my son or daughter will draw the winner from a hat on December 24th. Merry Christmas and good luck brothers. This is in Christmas thread because computer is down and had to use my phone but couldn't figure out how to do a link. Maybe someone could help and change it. If need be.

 

[redfin]

Well the knife is coming along nicely. Here's the sheath being wet formed to the knife. Sorry for not posting much on it last week or so just having life issues with losing a job and sick kids. View attachment 470962

Beautiful work.