ImpressiveHavent seen one break like that before.
You could tell pulley was wobbly in there. Now I know why.
View attachment 912213View attachment 912214View attachment 912215
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
What was the Stihl part number for the star washer?, it’s listed on your receipt. Likely those are used on FS string trimmer fuel caps.
Here are some tiny 3/16” hose clips, but may be a loose fit as he states they fit 5mm too.
https://www.ebay.com/itm/265164053271?hash=item3dbd025b17:g:uCkAAOSwfnlgowf5
You can tell which saw was used most and which was back up. Recoil goes with the saw on left. Needed it to test with.
Neither dont seem like much time on them though.
Older guy lived in town with some trees.
Neither dont seem like much time on them though.
Older guy lived in town with some trees.
Well since I needed a shell for recoil on the thin ring one above. Whats another 3.7 to the parts stash. Just bought whole saw instead of just a recoil.
JYARNO
New Member
I knew it had that power sharp crap and 2300. But didn’t catch it was a 2300AV till just now.
Has a weird tool less tensioner deal too
So that’s how they did that. 
Runs squirting mix in carb.
Fing horrible design for T handle. Little guy hurts with that pos handle even.
Has a weird tool less tensioner deal too
So that’s how they did that.
Runs squirting mix in carb.
Fing horrible design for T handle. Little guy hurts with that pos handle even.
What is the initial settings for H & L jets on a 4218AV with statos carb. Many thanks
They made so many variants it is hard to keep track, but they are good little saws.I knew it had that power sharp crap and 2300. But didn’t catch it was a 2300AV till just now.
Has a weird tool less tensioner deal too
So that’s how they did that.
Runs squirting mix in carb.
Fing horrible design for T handle. Little guy hurts with that pos handle even.
View attachment 912688View attachment 912689View attachment 912690View attachment 912691View attachment 912692View attachment 912693View attachment 912694View attachment 912695
I posted that here in thread just recently. I would have to search just like you can.
Found it on my website faster. 
http://chainsawrepair.createaforum.com/poulan/engine-speed-issue/msg86513/#msg86513
Poulan 4218 carb settings were L 2 and H 1.75
Green strato was L 1.75 and H 1.6ish on new carb.
http://chainsawrepair.createaforum.com/poulan/engine-speed-issue/msg86513/#msg86513Poulan 4218 carb settings were L 2 and H 1.75
Green strato was L 1.75 and H 1.6ish on new carb.
Thanks JJ, I guess I was just being lazy.Found it on my website faster.
Poulan 4218 carb settings were L 2 and H 1.75
Green strato was L 1.75 and H 1.6ish on new carb.
I just did one for a pawnshop (I tinker for them) & did 1 turn out each & fired right off.
Your humidity, heat, & altitude will determine carb tune.
Was going to buy a recoil shell for the one 3.7. But why buy a recoil when you can just buy a whole 3.7 thin ring saw being sold as non runner unless fed prime.
Thin ring top looks good too.
Thin ring top looks good too.
Lets just say no more tygon 4040 lines going in these.
First time trying the echo oem line in the small top handles. Loving this so far.
What I use in the bigger saws all the time. But thought I would try this over the Tygon 4040.
First time trying the echo oem line in the small top handles. Loving this so far.
What I use in the bigger saws all the time. But thought I would try this over the Tygon 4040.
Echo #90014, the 3mm X 5mm size?
Have always used that if the OD fits the gas tank hole.
Have always used that if the OD fits the gas tank hole.
3x5 yep. Just never thought about it fitting these till yesterday.
So one less line to buy. As I buy this in 26' rolls in 2 sizes.
I put them all up for sale on my CRG. Little guy for $30 pending local pick up already.
Hadnt even had a chance to clean them up a bit. Just doing what matters. Run cut
Hadnt even had a chance to clean them up a bit. Just doing what matters. Run cut
I’ll still need to clean outsides. But new echo oem fuel lines. New tank vent with new duckbill.
3.7 3700 61cc thin ring PHO
3.7 3800 61cc thick ring PHO
All start and run.
Do have some D176 bars if needed. Just cost you more for bigger box and shipping weight.
PM with any trades etc
Also have a 3.7 red thin ring with nice topend I am going to part out instead of going through.
Here are the 2 3.7 61cc in red. thin and thick ring. One had that PS knob. Internals removed.
3.7 3700 61cc thin ring PHO
3.7 3800 61cc thick ring PHO
All start and run.
Do have some D176 bars if needed. Just cost you more for bigger box and shipping weight.
PM with any trades etc
Also have a 3.7 red thin ring with nice topend I am going to part out instead of going through.
Here are the 2 3.7 61cc in red. thin and thick ring. One had that PS knob. Internals removed.
Breaking that parts saw down today. 61cc thin ring chrome bore
JMO that tool less tensioner is a worthless POS IMHO on that 2.3av.
I thought to myself. hmmmm my 2000 I bought new in 94 needs that handle AV.
I thought to myself. hmmmm my 2000 I bought new in 94 needs that handle AV.
