20" 3/8 LP Bar?

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Loops can be made in any length.

Some guys mill with 3/8 low profile chain ( couple of threads on this), and may want the longer loops.

To make things worse, Oregon makes a full sized 3/8 pitch chain they call 'LP', that does not mean 'low profile'!

http://www.oregonproducts.com/pdf/chain/72LP_FB_0800.pdf

Philbert
 
I'm betting on a double mistake.....should be 62DL on an 18" A041 bar, on a gazillion little Poulan/Craftsman/Homelite/Echo.
 
I bought a bunch of boxes of 80 drive link of the short cutter Oregon 91vx off ebay perhaps 5 years ago. They were even less money than that.

If you look at that sellers other listings that same chain is offered in quite a few lengths. Some with free shipping some not.
 
I know it varies but my .325 18" chains on my Echo and Maruyama are 72 dl. My Echo 490 20" is 78dl.
 
I know it varies but my .325 18" chains on my Echo and Maruyama are 72 dl. My Echo 490 20" is 78dl.

My apologies, the heading did state 3/8, not .325. And I get on the grandkids for not reading correctly!!
 
My 20" LP bar from LCS. Not 72DL though. ;) They had 68DL and 70DL LP listed at one time.

With 3/8 7T rim 68DL was to short and 70DL was to long. 69DL chain was just right.

20″ GB Arbor Tech Bar – GBF PO20-50WR – A041 Mount – 3/8″LP .050 http://leftcoastsupplies.com/product/20-gb-arbor-tech-bar-38lp/

Specs in sales ad. 20″ GB Arbor Tech Guide Bar

Bar Specifications:
Length 20″
Pitch 3/8″ LP
DL 68
Gauge .050″
Mount A041

pppicco%20002_zpsvsyi5ymv.jpg
gbbars20picco.JPG
 
My 20" LP bar from LCS. Not 72DL though. ;) They had 68DL and 70DL LP listed at one time.

With 3/8 7T rim 68DL was to short and 70DL was to long. 69DL chain was just right.

20″ GB Arbor Tech Bar – GBF PO20-50WR – A041 Mount – 3/8″LP .050 http://leftcoastsupplies.com/product/20-gb-arbor-tech-bar-38lp/

Specs in sales ad. 20″ GB Arbor Tech Guide Bar

Bar Specifications:
Length 20″
Pitch 3/8″ LP
DL 68
Gauge .050″
Mount A041

pppicco%20002_zpsvsyi5ymv.jpg
View attachment 582889

Is that picture what you call just right? The bar tail is even with the edge of the clutch drum. Oil feed placement the reason you do not want it any closer to the sprocket.

I actually bought a couple of those at the earlier price. I think I went 67 for 6 tooth and 68 for 7 tooth. Maybe I ground the tail just a bit to make it work, the Stihl chain is pre stretched, it does make a difference when it is close. Inboard clutch does have it's advantages if things are tight. Kind of heavy the Genuine Stihl bar that calls for 61 but works good with 62 on the 7 tooth drive is the one I use most of the time. I modify bars not mufflers and porting.
P1010139.JPG
 
I know this is an old thread, but this is one of the only references that comes up when someone is searching for a 3/8” LP bar. So, to make it easier for other people, since all the links above are dead.

https://www.baileysonline.com/cannon-supermini-3-8-low-profile-chainsaw-guide-bars.html
Cannon 20" SuperMini Chainsaw Bar (72 Drive Links) CSM-H1-20-50-3LM
SKU CSM H1 20 50 3LM

And there is even one available that is 32" long!
 

Latest posts

Back
Top