880 is hitting rev limiter at 10,800

[hoss]

OK..........What would you set it for milling 10,000 or lower? (after it's broken in)


Many Thanks,
Gary

Yes richening it up a bit for milling never hurts.

 

[RED-85-Z51]

Mostly by it's operator.







(man that was to easy)

No its supposed to be limited by the choke/air vane...now it is limited by the fact the Breakerless ignition has gone out.

I have a good TS-350 to swap the coils, also now have a Spare Tilly HL-166A.

Anyone ever swapped a big Tilly onto a stock saw, like say a Tilly 314G?

 

[Trigger-Time]

Took Lake's advice, taped tach to saw. In cut, she was running
8,000 rpm

Cut some Bur Oak Cookies

Yup, idle is little high.........

 

[Lakeside53]

8K in the cut for decent sized wood is fine.....

 

[Trigger-Time]

8K in the cut for decent sized wood is fine.....

Thanks..............just wanted to be sure, didn't want to mess it up, right off.


Gary

 

[Lakeside53]

So.... do you like it?

 

[Trigger-Time]

So.... do you like it?

Yes Sir..........to tell the truth, still a little nervous with it.
but that's how I was going from 036 to 460 and then
again when moving up to 066.

 

[Lakeside53]

lolol So.. what's next?

 

[Trigger-Time]

lolol So.. what's next?

:hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange:


You ask me that a couple years ago when I bought 460, I never in
my wild's dream's......................

 

[Tzed250]

lolol So.. what's next?

Only one place to go....

 

[Trigger-Time]

Only one place to go....

Will go 090, before I go their

 

[Tzed250]

Will go 090, before I go their

Soon it will be about the same money...:hmm3grin2orange:

 

[Trigger-Time]

Soon it will be about the same money...:hmm3grin2orange:

If I add anything else.........It will have to fall in my lap and be

CHEAP, CHEAP, CHEAP!!!!!!!!

 

[Tzed250]

If I add anything else.........It will have to fall in my lap and be

CHEAP, CHEAP, CHEAP!!!!!!!!

There went the bikesaw and the 090...

 

[Trigger-Time]

There went the bikesaw and the 090...

Bike saw yes.........but you never know when you mite come across
070 or 090. I have lot of :Eye: :Eye: out their looking.

 

[Tzed250]

Bike saw yes.........but you never know when you mite come across
070 or 090. I have lot of :Eye: :Eye: out their looking.

I know where an 090 for sale is...not to bad a price either...I passed on it earlier this year...

 

[Lakeside53]

:hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange:


You ask me that a couple years ago when I bought 460, I never in
my wild's dream's......................

Enabling my only role.. the choice is yours :greenchainsaw:

 

[2dogs]

Lake is there a particular model of 088/MS880 that is best for my use? I would use it falling and bucking redwood and fir. It would not get alot of use but I want to be able to run a 4' bar and 404 chain, mostly for redwood. Or would I be better off with an 084 or an 090? Let's pretend cost is not an issue and that my wife will never find out.

What is important is availabilty. I will need to make this purchase in the next week or 2.

 

[Lakeside53]

There is only one model of MS880 available... with a few bar options. iFcost is not an issue, buy new.


The 084 is hard to find in good shape (and parts...), and the 090.. well, if you like antiques..

 

[brncreeper]

I like my 088, it handles a 41” bar with 404 chisel chain just fine. RPM’s are right around 12,300, it seems to like it.opcorn: