Christmas Giving 2015
- Thread starter blsnelling
- Start date
Help Support Arborist Forum:
calebng15
Always lookin' for somthing to cut!
I've got a 20in bar!
fearofpavement
Trying them all
on the 20" bars, some take 70dl and some 72dl depending on the brand of bar and saw it fits on.
These are 72 or 84 DL. I can cut down to 70 and re-spin if needed.
What gauge? 058?
calebng15
Always lookin' for somthing to cut!
Pm sentNobody claimed this new Oregon bar yet. If it helps I can spin a new chain for it too.
It must've been the chain I threw in with it. [emoji6]
I'm just getting home in 15 minutes after a day that started at 4 AM… I'll try and stop in the shop and check if those were 20 inch or 24 inch.
Shoot. New bar WITH a new chain. I couldn't resist. You the man
)Sorry man, they are 24" 84 DL Carlton A2 chains.
I have a Forester brand replacement bar tip up for grabs. It is a 3 rivet style that fits the 3003 stihl bars. It replaces stihl # 3003-650-2551. It is Forester #ST38 New in package.(not my pic below)
Merry Christmas!
CLAIMED
Merry Christmas!
CLAIMED
fearofpavement
Trying them all
I'm needing a 3/8 tip for a Stihl bar but I think it's the older style wide nose bar. I'll get a width. If this one fits, I'm putting in my request.
Mike Gott
ArboristSite Guru
That's what I use but I've already got a couple gifts so somebody else should take advantage of his this fine offer
Sent from my iPhone using Tapatalk
Here are some chains for folks who can use them. First, a pair of unused 3/8"x0.050"x81DL loops.
Next, some chains from a collection of rental chains. They have been used for one rental, then replaced with a new chain. Most are still sharper than most of the chains I see on used saws and all have lots of life left in them.
I'm offering 4 pairs of 3/8"x0.050"x72DL lops and 5 pairs of 3/8"LoProx0.050"x57DL. Because the small loops are an odd size (certainly they are for my saws), I will shorten them to whatever DL count is needed. Here is a sample of each type:
One pair of loops per person, please. I'll cover the postage.
P.S. I still have the two pair of Caber rings, 42mm x 1.2mm. They should fit an early 025. The later 025s and MS250s have a 42.5mm piston. Check your measurements to be sure they'll fit in your refresh/rebuild. I believe these also fit the FS450 trimmer and Solo 645.
Next, some chains from a collection of rental chains. They have been used for one rental, then replaced with a new chain. Most are still sharper than most of the chains I see on used saws and all have lots of life left in them.
I'm offering 4 pairs of 3/8"x0.050"x72DL lops and 5 pairs of 3/8"LoProx0.050"x57DL. Because the small loops are an odd size (certainly they are for my saws), I will shorten them to whatever DL count is needed. Here is a sample of each type:
One pair of loops per person, please. I'll cover the postage.
P.S. I still have the two pair of Caber rings, 42mm x 1.2mm. They should fit an early 025. The later 025s and MS250s have a 42.5mm piston. Check your measurements to be sure they'll fit in your refresh/rebuild. I believe these also fit the FS450 trimmer and Solo 645.
The 57DL loops will fit some ECHO 16" bars, and some Carlton 16" bars used on HD rentals.
Philbert
USMC615
Wood's Tougher Than Woodpecker Lips...
PM'd.
