climber gets arm burned by overloaded rigging rope when rigging rope fails

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Stayalert

ArboristSite Operative
Joined
Jun 13, 2011
Messages
302
Reaction score
84
Location
Norwich, VT
Not really excited to share this but feel obligated....

The rigger, groundie, and climber were me, myself, and I....

I took too big a bite when removing an ash limb the other day as part of a piece by piece removal.....

I had an 11mm rope supported by a natural crotch tied (bowline) to a block. the base was trunk tied. Through the block I had another 11mm rope tip tied and to a porta wrap on my truck...

I was planning to slowly cut the limb at the butt end of the limb (which was about 20 feet off the ground) and as the tips came within reach - cut weight off with my poles saw from the ground, then lower the rest of the stem...

I was in spikes and climbed with a flip line to the butt end of the limb, The rope holding the block ran up the trunk I was climbing and was against the trunk and within the "circle" created by my harness and flip line. With my two tie ins secure I started to cut the limb.....

As the rigging tightened up, I turned off and attached the saw to my harness and As I prepared to climb down, the line holding the block failed at the bowline knot holding the block - and the rope exploded with a sound not unlike a shotgun blast. The block was driven into the ground a few inches, the rope that had been holding the block released its tension and burned the inside of my arm at the elbow.

I climbed down, did a bit of first aid and worked the rest of the day, happy in the thought that it could have been much, MUCH worse....
 
This kind of reminds me of the scene in The Guardian where he has all of the trainees in the tank full of ice water. The commander calls Kevin Costner over and says you were just supposed to teach them about the dangers of hypothermia. Kevin looks at his watch and says, "in about 5 minutes, sir, they'll get it." You were lucky, and I know you're a way better climber than you were yesterday, because now you know how fast it can go bad. Glad you're ok, and get a decent bullrope, and never let a pick cross you. Jeff
 
doing all that by yourself

Been there done that. I am not an arborist by any means. I am a woodburner. I have learned from my dad, uncle, and neighbor growing up about how to rope and knot things differently. I would say that yes if you have the equipment and means..use it, but most of what I did growing up was a 3 strand hemp rope and watched my uncle many of times tie off the limb wrap the rope 5-6 times around a higher branch(creating the friction) and then once or twice around a branch close to his reach. I have learned when you work with non-experienced people that the more safety you build into your approach the less chance in bad things happening. That being said. My cousin(limited experience) said just throw the rope over here and cut..OK..MR BADASS muscle freak..I did as he suggested..cut about halfway through approx. 40 foot up..checked rope angles and adjusted a tad..ripped enough to drop..all of a sudden knocked his antenna off the roof ran down his shingles. 1-1 mechanical advantage isn't very good unless your a BADASS..oh wait..that doesn't help either. Take the variables out. use a good rope..wrap the trunk and don't climb up and down..make your job easier. nuff said
 
aaah ouch that 'll sting n leave a mark hope ye heal fast thanks for the post to share save other grief

I reread your story did best to follow lost it a bit thou think i understand the weakest link in the chain let go, what you reckon was cause

11mm static tree rig rope (the good stuff) most often has 2500 to 3500kg break max load so I'm thinkin its SWL safe work load adding a in line knot would be / factor of 8 so 300 to 600 kg. Was the log about that size 300 400 kg or about a v8 motor 550lb was the rope getting old n tired or was it dynamic climb line which can have much less max break.
 
weakest link was (as you correctly point out) was the in line knot in the rope. Rope isn't dynamic but it has seen quite a bit of use...The rope that broke is now ~4' shorter....The ends see most of the work and had I shortened it myself with a knife (removed the high use/"worn" end) as part of my rope maintenance, it might have held....I also took too big of a piece....
 
weakest link was (as you correctly point out) was the in line knot in the rope. Rope isn't dynamic but it has seen quite a bit of use...The rope that broke is now ~4' shorter....The ends see most of the work and had I shortened it myself with a knife (removed the high use/"worn" end) as part of my rope maintenance, it might have held....I also took too big of a piece....


thanks kind regards :msp_thumbup:

we always take too bigg a piece its in our DNA:msp_rolleyes: others who may read your thread will now be checking their rope systems & perhaps saving them grief.:msp_thumbup:
 
thanks kind regards :msp_thumbup:

we always take too bigg a piece its in our DNA:msp_rolleyes: others who may read your thread will now be checking their rope systems & perhaps saving them grief.:msp_thumbup:

LOL! def. true......I'm healing pretty quickly, and lucky for me I can work while I heal......Sadly its right on the inside of my elbow and will be scabbing and breaking (because of all of the movement at the joint) for many moons.....
 
How about some details on the rope that was holding the block was (brand and condition)? Glad your not seriously hurt. Thanks for sharing.
 
LOL! def. true......I'm healing pretty quickly, and lucky for me I can work while I heal......Sadly its right on the inside of my elbow and will be scabbing and breaking (because of all of the movement at the joint) for many moons.....

consul yourself that hot chicks dig tuff blokes with scars :msp_rolleyes:
 
OOOOOUUCH! That looks like it hurts! I had one that burned my armpit.........ya, my arm pit. Was on the ground running ropes, had a big lead that I wanted to let run, but had to open a Pepsi (priority's right!) So I pinched the line in my armpit and my climber let it go, it ran alright. Took the hair and skin. Hurt like hell, but not sure which was worse, the burn or the healing. Hair trying to grow thru a scab :cry:, it sucked! It was my fault, I should have been paying way better attention to him. But I needed that Pepsi pretty bad.
 
Not really excited to share this but feel obligated....

The rigger, groundie, and climber were me, myself, and I....

I took too big a bite when removing an ash limb the other day as part of a piece by piece removal.....

I had an 11mm rope supported by a natural crotch tied (bowline) to a block. the base was trunk tied. Through the block I had another 11mm rope tip tied and to a porta wrap on my truck...

I was planning to slowly cut the limb at the butt end of the limb (which was about 20 feet off the ground) and as the tips came within reach - cut weight off with my poles saw from the ground, then lower the rest of the stem...

I was in spikes and climbed with a flip line to the butt end of the limb, The rope holding the block ran up the trunk I was climbing and was against the trunk and within the "circle" created by my harness and flip line. With my two tie ins secure I started to cut the limb.....

As the rigging tightened up, I turned off and attached the saw to my harness and As I prepared to climb down, the line holding the block failed at the bowline knot holding the block - and the rope exploded with a sound not unlike a shotgun blast. The block was driven into the ground a few inches, the rope that had been holding the block released its tension and burned the inside of my arm at the elbow.

I climbed down, did a bit of first aid and worked the rest of the day, happy in the thought that it could have been much, MUCH worse....

I hear salt and lime juice work wonders for those types of burns.
 
How about some details on the rope that was holding the block was (brand and condition)? Glad your not seriously hurt. Thanks for sharing.

PMI static 11mm rescue type rope that i've used pretty hard with alot of success...Condition wise? I pack all my ropes and am pretty methodical about culling out damgaed pieces/ends/etc.......I over loaded it and it failed. I'm currently shopping a 5/8 or 3/4 rigging rope or 2.....
 
PMI static 11mm rescue type rope that i've used pretty hard with alot of success...Condition wise? I pack all my ropes and am pretty methodical about culling out damgaed pieces/ends/etc.......I over loaded it and it failed. I'm currently shopping a 5/8 or 3/4 rigging rope or 2.....

Well you don't really want to be shocking static line on a regular basis. It's meant for repelling, constant steady load.
 
PMI static 11mm rescue type rope that i've used pretty hard with alot of success...Condition wise? I pack all my ropes and am pretty methodical about culling out damgaed pieces/ends/etc.......I over loaded it and it failed. I'm currently shopping a 5/8 or 3/4 rigging rope or 2.....

How much did the piece weigh and how far did it fall before the slack was out of it?
 
How much did the piece weigh and how far did it fall before the slack was out of it?

The rope that failed wasn't taking the weight of the limb...only a portion of it....

There was no slack. This was a limb off the side of the main trunk. I was cutting the butt end of the limb in order to "lower" the tips of the limb to within reach (from the ground) of my pole saw. As I proceeded with cutting the butt end, the limb "drooped" like I wanted it too.....After I stopped cutting and prepared to climb down, the rope holding my block failed, "kapow!"

The limb weighed too much.
 
The rigger, groundie, and climber were me, myself, and I....

This is a reminder....never work alone!
Safety, safety, safety.....
 
The rope that failed wasn't taking the weight of the limb...only a portion of it....

There was no slack. This was a limb off the side of the main trunk. I was cutting the butt end of the limb in order to "lower" the tips of the limb to within reach (from the ground) of my pole saw. As I proceeded with cutting the butt end, the limb "drooped" like I wanted it too.....After I stopped cutting and prepared to climb down, the rope holding my block failed, "kapow!"

The limb weighed too much.

Sure must have been heavy. Was it 1000 lbs or more?
 

Latest posts

Back
Top