Project Stumpbroke 395xp Stage 2

[Hedgerow]

That's awesome ! Be the powerhead weigh's close to 25lbs just a guess. Those old Oly's are some neat machines. Nice build sounds/runs great. I think we should do a big log challenge hahah.

Never count out a stumpbroke 395 for a big bar challenge...
I believe Durand will have his there too if he can make it over from TN...
I've run it... It's nice... Those saws will run with 6 cubes...

 

[moody]

Never count out a stumpbroke 395 for a big bar challenge...
I believe Durand will have his there too if he can make it over from TN...
I've run it... It's nice... Those saws will run with 6 cubes...

From the video's I've seen they've got a real nice grunt to 'em.

 

[sam-tip]

I cant wait to see the vid for its big brother. I sent both saws down in the same box. Both getting stage 2. I never ran the 3120xp. Just shipped it straight to stumpy.

Sent from my SCH-I800 using Tapatalk 2

 

[sam-tip]

PS there is plenty of room in trailer for saws. 8x18 ft with V nose trailer for saws to GTG.

Sent from my SCH-I800 using Tapatalk 2

 

[Stumpys Customs]

Never count out a stumpbroke 395 for a big bar challenge...
I believe Durand will have his there too if he can make it over from TN...
I've run it... It's nice... Those saws will run with 6 cubes...

The hammer might want in on some of the big bar challenge.:msp_wink:

 

[andydodgegeek]

The hammer might want in on some of the big bar challenge.:msp_wink:

If your talking like a coconut 7 layer or rice crispie bar challenge I am all in!!!:msp_w00t:

 

[komatsuvarna]

Never count out a stumpbroke 395 for a big bar challenge...
I believe Durand will have his there too if he can make it over from TN...
I've run it... It's nice... Those saws will run with 6 cubes...

I'm hoping to make it !!!!

Can't say I have anything fo a big bar challenge though....

I like short bars better now days :msp_w00t:

 

[Roll Tide]

I'm hoping to make it !!!!

Can't say I have anything fo a big bar challenge though....

I like short bars better now days :msp_w00t:

I may have a saw for a long bar challenge

 

[Hedgerow]

I may have a saw for a long bar challenge

What? That tired ole orange thing???
C'mon out!!!
May even have the state Husqvarna rep in attendance..
These things would blow his mind...

 

[johnfawn2000]

got a low hour 395xp that will be getting the stage 2 treatment here. These are some nice saws right off the shelf.

stumpys customs, when is good time to call and a phone number.i may have over looked the number,sorry the tarheel pest.

 

[WKEND LUMBERJAK]

stumpys customs, when is good time to call and a phone number.i may have over looked the number,sorry the tarheel pest.

His email is on the bottom of his post.

 

[sam-tip]

Watch the video. The phone number is at the end along with email address.

 

[Stumpys Customs]

stumpys customs, when is good time to call and a phone number.i may have over looked the number,sorry the tarheel pest.

PM sent.:msp_thumbsup:

 

[Termite]

I may have a saw for a long bar challenge

I am wondering, is it a Stiih?

 

[moody]

I am wondering, is it a Stiih?

I'd be tempted to say it's his 395. But it does make a guy wonder.....

 

[Stumpys Customs]

Here's big brother
http://www.arboristsite.com/chainsaw/232204.htm

 

[sam-tip]

I am one proud daddy. I counted 3 seconds faster than the 395 with 404 chain vs 3/8.

WOW

 

[Stumpys Customs]

I am one proud daddy. I counted 3 seconds faster than the 395 with 404 chain vs 3/8.

WOW

SOrry, it was the same bar & chain for both saws. 395 had a 7 pin rim & the 3120 had an 8. Both are beasts in their own right.

 

[excess650]

I am one proud daddy. I counted 3 seconds faster than the 395 with 404 chain vs 3/8.

WOW

7 pin .404 is just slightly smaller(94%) than 8 pin 3/8, so that 3120 should RIP with 7 pin .404!

BTW, nice job on BOTH saws!

 

[Roll Tide]

I'd be tempted to say it's his 395. But it does make a guy wonder.....

You would be correct.