Search results

Sorry to see the bad luck... I've got a new 460 sitting on the display here in SE Ohio...

Send Stumpy a PM, my 361 did something very similar after porting. Sent from my iPhone using Tapatalk

If you're looking for work and play, a side by side is what you need... I had a 350 Rancher with about 6K miles on it and it was great, but no comparison to my Kawasaki Teryx...

I don't have mine handy, but if I recall correctly, it is 18x24 inches, 1 inch OD tube, spaced about 1.5 inches apart.

I'm sure there is a hydraulics shop somewhere near you...look around a bit and see if you can find one. I had the same thing happen on a small cheap TSC 11 GPM pump that runs my conveyor and instead of 200 bucks for a new one, I took it and they were able to get it working again and it only...

The distributor for your dealer should be Bryan Equipment in Loveland, OH...call them and check on your dealer's story...

Just a little rain and wind here...maybe 30-35 MPH gusts... Hoping that the rain is all we get... Good luck to you guys further east...I'm still having nightmares from the hours I worked after the frontline winds that hit here came through back in June.

I love my ported 361, but if I had it to do again, I would have sold that saw and gotten a new 261 and had it worked over.

I talked to him last week, and looks like some others have talked to him since...he was doing fine and well then, and I'm sure he will be back. Just some things to get in order. Stumpy is the man! In before the lock down...

I cut 300+ cords a year for commercial firewood, and all my saws will ever see is RMC Stihl chain...it's worth its weight in gold to me. I've tried Carlton, Oregon, and Total and the only thing that comes close is the Total. Unfortunately, my other supplier can no longer get it, and my Stihl...

Good luck...I've got an older Briggs that was rarely used off a tiller that I put on my conveyor and it refuses to start half the time without working yourself to death.

Lookin good! How long till this one will be going up for sale?

I've got one of those motors on my conveyor that did the same thing on Wednesday... Break it loose with a pipe wrench, and add oil. Run it for a minute or two, then drain all the oil out. Then fill it back up and run it for 20 minutes or so and change the oil again. I have put 9 hours on...

Shoot me a PM...I might be able to help you out...

441 MTronic here. I bought it about a month after they were released and threw it into production firewood. I'm guessing it's had 200 tanks put through it in the last year and a half. Zero issues, I would buy another one tomorrow. It went from 20 degree winter, to 110 degree summer and didn't...

Send that puppy to Stumpy for some Stumpbreaking...it'll wax a stock 440.

I've got 2 of them that are run in a commercial lawn business and they get beaten up day in and day out. No issues at all minus one muffler bolt coming loose. I'd buy more to replace them in a heartbeat if needed. If only I could make my 4 mix trimmers run as well as the simple old transfer...

The 441 I have and the 372 I have yes. Then again, the 361 that Stumpy did for me is stronger than the 372, so take that for what it's worth.

I pulled the screen out of mine, and enlarged that hole, then drilled 2 new 1/2 inch holes below it. Do the recalibrate and it'll be a very good running saw. I've got a 372 Husky that's been worked over by a reputable builder on here, and I would put my 441 up against it and expect an even...

Guys, I've got the perfect place for a get together, big wide open field, room for tents and campers, lots of parking, and easy to find off a major highway. I'm thinking sometime in early October, if there's any interest. I've obviously never hosted a GTG before, and haven't been to one, just...