Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
ANewSawyer
Addicted to ArboristSite
So, I was looking at the IPL as I put it back together. Is there supposed to be an oring somewhere on the gas cap? I know mine seeps gas so that might be a problem.
There's a flat black gasket. If it leaks an "O" ring will work fine. Over tightening the cap can break the filler neck on the tank so don't use a tool to tighten it.
Hi Mark!
ANewSawyer
Addicted to ArboristSite
I wish I could like my own post... 
Hey Tim...
ANewSawyer
Addicted to ArboristSite
Would a 0.058 bar and chain work on my 3700?
Hoping to get to run my Red 3700 tomorrow. Got a storm damaged half of a tree to remove that has been there since summer.
Hoping to get to run my Red 3700 tomorrow. Got a storm damaged half of a tree to remove that has been there since summer.
Sure as long as the bar, chain, and sprocket on the clutch all match. Like 3/8ths.
ANewSawyer
Addicted to ArboristSite
Ok, I will make sure it is 3/8ths.
ANewSawyer
Addicted to ArboristSite
Hmmm,wanting to convert this puppy to a rim sprocket setup. Will this work with 0.050 and 0.058? http://www.baileysonline.com/Chains...ocket-SD7-Standard-7-Spline-3-8-x-7-Tooth.axd
astnmacgto
Carnac The Magnificent
It should as long as yours is a standard spline, if I had to guess it's probably small spline but idk
Spur sprockets were standard issue. I assume you have a spur. If so, you'll need to track down a splined drum. Oregon no longer makes the splined drum and rim assemblies unfortunately. They do show up on Ebay occasionally. 28187x is the PN. Some outdoor power equipment suppliers may still have old stock as well.
I like this Oregon cross-reference chart.
All the rims I see don't specify, only 3/8 or different, I assume it accepts all widths?
-•------------------------------------------------------------
Just a home owner that likes the older better made machines
Craftsman 3.7 x2
Husqvarna 36
-•------------------------------------------------------------
Just a home owner that likes the older better made machines
Craftsman 3.7 x2
Husqvarna 36
astnmacgto
Carnac The Magnificent
Yes they do, and u think the 3/8lp also uses a full size 3/8 rim I've never found any that were made for lp specifically
A rim will work on both .058 or 050 drive teeth. You just need to make sure the rim matches the clutch drum you are going to use.
ANewSawyer
Addicted to ArboristSite
I have seen the rims and the setup both. Trying to get some spare rims with the setup. The 28187x is available here: https://www.oregonpartswarehouse.com/oregon-28187x
So what's the difference between 7 and 8 spline, 3/8 standard rim? Faster cutting speed less torque?
-•------------------------------------------------------------
Just a home owner that likes the older better made machines
Craftsman 3.7 x2
Husqvarna 36
-•------------------------------------------------------------
Just a home owner that likes the older better made machines
Craftsman 3.7 x2
Husqvarna 36
ANewSawyer
Addicted to ArboristSite
I believe an 8 pin would be less torque more chain speed opposite for a 7 pin. I would tend to stick to 7 pin with 18" and over bars. Less than 16" you might could get away with 8 pin on a 3700.
ANewSawyer
Addicted to ArboristSite
Meant to ask, what should I set the carb needles to initially? I have High and Low both at about 2 turns out.
Got it: http://www.ebay.com/itm/OREGON-SPROCKET-28187-/192024911993?hash=item2cb593a079:g:AhEAAOSwXyVYJh-p
Got it: http://www.ebay.com/itm/OREGON-SPROCKET-28187-/192024911993?hash=item2cb593a079:g:AhEAAOSwXyVYJh-p
Similar threads
