redunshee
Addicted to ArboristSite
Don't recall ever getting a free saw. You suck!
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
Sty57
Tree Freak
That is a nice 4000 you have there. It does seem a little slow on the Trading post as I haven't gotten any nibbles on my little Craftsman either.
Morning Tim, can't sleep either?
redunshee
Addicted to ArboristSite
Yea. Lot of guys like to make stupid jokes or comments it seems. Will stick iit on Ebay later and put a lower but it now price.
Sty57
Tree Freak
I hear that, everyone has some smart aleck comment.
Got a box of parts too. 
Steve
Steve
seems like it goes in cycles. Remember a few years ago the 3450 3750 330 3700 4000 saws were getting big $$$. But you, Gregg, mike mark me etc were doing write ups all the time pics and vids too. I swear that drove up the demand. Maybe it's still like that on as, I was gone all summer
I'm no expert Bob, as I have never sold a saw!
You might want to hold your price if you put it on ebay. I have seen some 4000's go for some crazy $$$ before on there. Probably not, if you or I were selling, but you never know. Have seen them fetch $400 before. Crazy I know. To me though, they are worth as much as an equivalent "modern saw". But to some, lack of parts availability no doubt hurts that. I LOVE a good 4000!.png "Love :heart:")
Gregg,
Nope. Not much last night. Feeling it now.
Ha my 7 month old was doing backflips in our bed from 2am to 4am. My alarm goes off at 5
Its hell to reach "geezer" status ain't it Tim.
I have that problem as of late it seems. Trouble sleeping at night, get up early, then about 2 hrs. later feel like you could go to sleep standing up. Gregg,
Its hell to reach "geezer" status ain't it Tim.
Gregg,
Yes it is not all good being a geezer to be sure. I feel for Joe as our kids were terrible sleepers. Up 6 or 7 seven times a night until after they were two years.
Not that bad yet.
I ran a 3700 against a J'red 630 and a Homie XL-76 yesterday in some hard dry ash. The 630 felt the strongest and the 76 and 3700 about the same. I used the same bar and chain and took vids to time them but the 3700 and the XL-76 videos wouldn't work. I'm thinking the sound get gets out of sync with the video part due to excessive noise.
I've had that issue with three cameras and I'm wondering if I'm cutting in close quarters is causing the sound to bounce around a lot (which I found out can cause this issue).
The 630 is by far the quietest of the three and maybe that's why that video survived.
All fun to run and good cutting saws to boot.
I've had that issue with three cameras and I'm wondering if I'm cutting in close quarters is causing the sound to bounce around a lot (which I found out can cause this issue).
The 630 is by far the quietest of the three and maybe that's why that video survived.
All fun to run and good cutting saws to boot.
Thanks Tim. Something to look forward to
blk05crew
I like 'em green
I haven't got to cut any since mid summer, especially with most of WA state on fire for so long. So I had to fire up the 5200's last night just to remember what they sound like and get a quick fix haha! And I took a picture just because.
Thanks for the manual fossil, that's going to help alot.
Steve
Steve
Well here she is before I tear into it.
Steve
Steve
Steve
3800 stock, 415 stock, 4500 stock, 6700 stock with slight mm under deflector, bigger 8000 carb.
blk05crew
I like 'em green
Hope this loads
Steve
So it's a 3400 or is it a 3700 like you said that someone put a different starter housing on?
