StihlGuitar
ArboristSite Operative
I even have a Walbro that I successfully bent the fuel inlet on and used on an 026. PM me if interested
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I even have a Walbro that I successfully bent the fuel inlet on and used on an 026. PM me if interested
StihlGuitar
ArboristSite Operative
I'm looking for a 371xp coil, clutch/bar cover, and possibly a top handle. Lots to trade or pay cash.
You can use pretty much any Tillotson HL as long as you have the low-profile fuel inlet/fuel pump. I'll post pictures later.
I have a junk 1-41 carb with the low profile fuel pump. I tried to put that part on an HL360 to fit to the 890 but that particular carb body itself was still too big and bumped on the floor of the airbox. So, it was back to the stupid Mac flatback. Maybe a nice used 070/090 carb would work...
Chris B.
Guarddog1
ArboristSite Guru
I would be willing to sell the tank assembly with intake boot air filter and everything to bolt the 044 carb on your 026 off this saw. If interested PM me.
http://www.arboristsite.com/showthread.php?p=1761836#post1761836
Yeah the modern 3** series carbs are usually too big. The carbs to look for are the high-number 1** and most of the 2** series. You may have to switch fuel pumps too.
Again, Nice info. Jacob.
What are the performance gains by
going to the tilly. Is it very noticeable.
Lee
chewbacca
ArboristSite Member
I need about 8 used standard spline 3/8 - 7 sprocket rims. I dont care if they are junk as long as they're not bent and the interior splines aren't chewed up. Anyone have some old previously replaced ones layin around they'd send me if I paid shipping? I'm makin a coupler between my saw and my lewis winch.
StihlGuitar
ArboristSite Operative
Stihl 075 Starter cup
Anyone have an 075 starter cup (the cup on the flywheel that is ribbed for his pleasure) I pilfered the recoil assembly off of an 041 for a freshly rebuilt 075, got about 3 pulls on the recoil string before it started missing. I don't know why they made this setup, unless my starter cup is abnormally warn out (road hard, put away unribbed...) Can anyone help me out? If they are cheap enough at a dealer, I'll get a new one, but you know how that goes...intake boot for an 036 is 30$!! Any advice? Any way to switch the starter system over to a better one?
Anyone have an 075 starter cup (the cup on the flywheel that is ribbed for his pleasure) I pilfered the recoil assembly off of an 041 for a freshly rebuilt 075, got about 3 pulls on the recoil string before it started missing. I don't know why they made this setup, unless my starter cup is abnormally warn out (road hard, put away unribbed...) Can anyone help me out? If they are cheap enough at a dealer, I'll get a new one, but you know how that goes...intake boot for an 036 is 30$!! Any advice? Any way to switch the starter system over to a better one?
HittinSteel
Addicted to ArboristSite
Looking for a nice clean 044/046. Would be willing to trade my 262xp and some cash for the right saw.
Got a pic of your 262?
redlinefever
ArboristSite Operative
Didnt like the carb setup ???????? why r u gettin rid of it????
john taliaferro
Addicted to ArboristSite
I need to find top & filter cover for ms 460. got extra bars 3/8 .50 20 25 16 to trade for 3/8 .63 got a 41" huskey bar i think its 3/8
I have what you need, pm me
051av
I need a couple of 051AV parts. I need a muffler in usable condition and there is a shroud that covers the outer part of the muff. If anyone can help I have some parts and/or $$$$$ to trade.
I need a couple of 051AV parts. I need a muffler in usable condition and there is a shroud that covers the outer part of the muff. If anyone can help I have some parts and/or $$$$$ to trade.
Logman
ArboristSite Lurker
245a / 55 husky
I need a cylinder and piston for a 55 husqvarna and a piston for a 245a poulan.
Thanks Jack
I need a cylinder and piston for a 55 husqvarna and a piston for a 245a poulan.
Thanks Jack
Anybody have a 246 piston or piston and cylinder? I don't want to put a cheap golf piston in a nice saw.
I just listed a complete 245A in the for sale section. It's a great condition runner though
Similar threads
