Pioneer chainsaws

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Sorry if this has been asked 100 times before but, the search is still broken.

Are p50,p51,p52 parts interchangeable?

For the most part they are. Early P50's used a mesh type air filter so the rubber carb box and top cover and top handle are different. The P52 uses a different coil and flywheel also.

What do you have in mind?
 
For the most part they are. Early P50's used a mesh type air filter so the rubber carb box and top cover and top handle are different. The P52 uses a different coil and flywheel also.

What do you have in mind?

I ran into a few parts saws and had someone looking for a p50 case. The nicest case I have is a p51 and I wasn't sure if that would help him.

Also trying to see how close I can get to a complete saw with the pieces I have.

Thanks
 
Pioneer NU17 Piston

Question for the Pioneer Experts out there.

I am looking for an after market piston for my Nu17 Saw.

I saw that someone had found a similar piston and machined it to suite but for the life of me i cannot find it again.

Any info would be great.

Thanks in advance
 
Question for the Pioneer Experts out there.

I am looking for an after market piston for my Nu17 Saw.

I saw that someone had found a similar piston and machined it to suite but for the life of me i cannot find it again.

Any info would be great.

Thanks in advance

Is your cylinder worn out? If not then the piston from a 600 series saw is the same as the NU17 the RA also,they are not too hard to find.
 
NU 17 Piston

Thanks for the info

Scored a good second hand cylinder from ebay. Will keep looking for a piston.

Thanks
 
Help/advice for P21

Aquired a P21 as a parts saw, Supposedly seized [starter cord all frayed &locked up]Rest looked OK [carb kit & new fuel line & filter] Starts & runs really good,Problem, on idle I get a ringing/jingle coming from the clutch/ sprocket Have replaced sprocket/clutch drum & bearing , slightly better but still tinging away, all thoughts/idea`s welcomed [Runs & cuts good & idles fine] Thanks.
 
A couple of my P series do that. Even with nos parts, it still does it. I believe it's the drum ringing, I just ignore it, knowing everything is proper.
 
Aquired a P21 as a parts saw, Supposedly seized [starter cord all frayed &locked up]Rest looked OK [carb kit & new fuel line & filter] Starts & runs really good,Problem, on idle I get a ringing/jingle coming from the clutch/ sprocket Have replaced sprocket/clutch drum & bearing , slightly better but still tinging away, all thoughts/idea`s welcomed [Runs & cuts good & idles fine] Thanks.

Al, our postal strike is supposedly over, your parts will be going out shortly.

I agree with Ed, they all seem to do that.
 
Al, our postal strike is supposedly over, your parts will be going out shortly.

I agree with Ed, they all seem to do that.

Thanks Ed & Chris Every thing seemed to be good, but it sounds like a blacksmiths shop on idle. We should get them altogether & see if we can tune them & form a handbell ringing group Al.
 
this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

I'd be grabbing that one up if I were you David. :msp_smile:

I'd tell you to grab it for me if it wasn't so dang far away.:msp_unsure:

Thanks Ed & Chris Every thing seemed to be good, but it sounds like a blacksmiths shop on idle. We should get them altogether & see if we can tune them & form a handbell ringing group Al.

:hmm3grin2orange::hmm3grin2orange:
 
New Finds

<a href="http://s789.photobucket.com/albums/yy180/PioneerP62/?action=view&amp;current=DSCF0151.jpg" target="_blank"><img src="http://i789.photobucket.com/albums/yy180/PioneerP62/DSCF0151.jpg" border="0" alt="Photobucket"></a>
<a href="http://s789.photobucket.com/albums/yy180/PioneerP62/?action=view&amp;current=DSCF0152.jpg" target="_blank"><img src="http://i789.photobucket.com/albums/yy180/PioneerP62/DSCF0152.jpg" border="0" alt="Photobucket"></a>
I picked theses saws up last week. A pair of P41 saws for parts, a P28 electronic and a P40. The older saws are a 2200, 2400 and I think the large green saw is a 700. Was originaly yellow but has a extra coat of green paint? The older saws do not fit my collection. Trading material for the P series saws or ???
 
Pioneers coming out of the closet

Well so to speak that is! Good finds you guy's.I got into a great garage sale last weekend and picked up some old tools that I will be posting on the Tool Forum and also a nice Husky
Lawrence185 CD
 
Back
Top