Pioneer chainsaws

[thomas1]

Sorry if this has been asked 100 times before but, the search is still broken.

Are p50,p51,p52 parts interchangeable?

 

[Arrowhead]

Sorry if this has been asked 100 times before but, the search is still broken.

Are p50,p51,p52 parts interchangeable?

For the most part they are. Early P50's used a mesh type air filter so the rubber carb box and top cover and top handle are different. The P52 uses a different coil and flywheel also.

What do you have in mind?

 

[thomas1]

For the most part they are. Early P50's used a mesh type air filter so the rubber carb box and top cover and top handle are different. The P52 uses a different coil and flywheel also.

What do you have in mind?

I ran into a few parts saws and had someone looking for a p50 case. The nicest case I have is a p51 and I wasn't sure if that would help him.

Also trying to see how close I can get to a complete saw with the pieces I have.

Thanks

 

[Arrowhead]

The P51 case will work fine on any P50.

 

[arcanus11]

Pioneer NU17 Piston

Question for the Pioneer Experts out there.

I am looking for an after market piston for my Nu17 Saw.

I saw that someone had found a similar piston and machined it to suite but for the life of me i cannot find it again.

Any info would be great.

Thanks in advance

 

[pioneerguy600]

Question for the Pioneer Experts out there.

I am looking for an after market piston for my Nu17 Saw.

I saw that someone had found a similar piston and machined it to suite but for the life of me i cannot find it again.

Any info would be great.

Thanks in advance

Is your cylinder worn out? If not then the piston from a 600 series saw is the same as the NU17 the RA also,they are not too hard to find.

 

[arcanus11]

NU 17 Piston

Thanks for the info

Scored a good second hand cylinder from ebay. Will keep looking for a piston.

Thanks

 

[P10]

Need a P10 (mark 1) pulley

Anyone know where I may purchase a rope pulley fora P10?

Mine has the spring catch on the backside broken.

 

[Little Al]

Help/advice for P21

Aquired a P21 as a parts saw, Supposedly seized [starter cord all frayed &locked up]Rest looked OK [carb kit & new fuel line & filter] Starts & runs really good,Problem, on idle I get a ringing/jingle coming from the clutch/ sprocket Have replaced sprocket/clutch drum & bearing , slightly better but still tinging away, all thoughts/idea`s welcomed [Runs & cuts good & idles fine] Thanks.

 

[Arrowhead]

A couple of my P series do that. Even with nos parts, it still does it. I believe it's the drum ringing, I just ignore it, knowing everything is proper.

 

[DSS]

Aquired a P21 as a parts saw, Supposedly seized [starter cord all frayed &locked up]Rest looked OK [carb kit & new fuel line & filter] Starts & runs really good,Problem, on idle I get a ringing/jingle coming from the clutch/ sprocket Have replaced sprocket/clutch drum & bearing , slightly better but still tinging away, all thoughts/idea`s welcomed [Runs & cuts good & idles fine] Thanks.

Al, our postal strike is supposedly over, your parts will be going out shortly.

I agree with Ed, they all seem to do that.

 

[DroppedP51]

this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

 

[Arrowhead]

this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

I'd be grabbing that one up if I were you David. :msp_smile:

 

[Little Al]

Al, our postal strike is supposedly over, your parts will be going out shortly.

I agree with Ed, they all seem to do that.

Thanks Ed & Chris Every thing seemed to be good, but it sounds like a blacksmiths shop on idle. We should get them altogether & see if we can tune them & form a handbell ringing group Al.

 

[DSS]

this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

I'd be grabbing that one up if I were you David. :msp_smile:

I'd tell you to grab it for me if it wasn't so dang far away.:msp_unsure:

Thanks Ed & Chris Every thing seemed to be good, but it sounds like a blacksmiths shop on idle. We should get them altogether & see if we can tune them & form a handbell ringing group Al.

:hmm3grin2orange::hmm3grin2orange:

 

[P62]

this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

I wish that saw was in my collection. Looks like a dandy for sure.

 

[P62]

New Finds

<a href="http://s789.photobucket.com/albums/yy180/PioneerP62/?action=view&amp;current=DSCF0151.jpg" target="_blank"><img src="http://i789.photobucket.com/albums/yy180/PioneerP62/DSCF0151.jpg" border="0" alt="Photobucket"></a>
<a href="http://s789.photobucket.com/albums/yy180/PioneerP62/?action=view&amp;current=DSCF0152.jpg" target="_blank"><img src="http://i789.photobucket.com/albums/yy180/PioneerP62/DSCF0152.jpg" border="0" alt="Photobucket"></a>
I picked theses saws up last week. A pair of P41 saws for parts, a P28 electronic and a P40. The older saws are a 2200, 2400 and I think the large green saw is a 700. Was originaly yellow but has a extra coat of green paint? The older saws do not fit my collection. Trading material for the P series saws or ???

 

[pioneerguy600]

this has come up on local auction site,
Looks a good saw One owner and never misstreated

View attachment 187546 View attachment 187547

That is a very nice looking P52, bet it was well looked after and likely has very low hours on it. Almost looks as nice as my P52.

 

[pioneerguy600]

Jeff,..I see you are still gathering up some heavy iron,..nice haul.

 

[WesternSaw]

Pioneers coming out of the closet

Well so to speak that is! Good finds you guy's.I got into a great garage sale last weekend and picked up some old tools that I will be posting on the Tool Forum and also a nice Husky
Lawrence185 CD