Swap meet...

[Eccentric]

Those will probably fit the Mac 73/77 as well. I've been told by some of the old-timers that several saws could use the same spur
sprockets. I bought a huge lot of 200+ spur sprockets about three years ago from a retired saw shop owner that gave me a
fairly comprehensive list of what they fit. There were spurs in there for just about every gear-drive saw ever made, except for
the 090G. There were even .375" pitch spurs for the gear-drive Macs using the 19/32" stub shaft.

Very interesting. I've seen NOS McCulloch gear drive sprockets in the original McPackaging. "Will fit all McCulloch gear drive chainsaws except 3-25, 4-30, 47, 49, 73, 77" (or similar wording) was printed on the packages. They probably can be used on those saws, even though they're not the "right" part. Do you happen to have any. 404-8 Homelite 1100/1130/3100G sprockets?

 

[Roanoker494]

I could use a good brake handle for a Husqvarna 365/372. Got a bunch of stuff around here, just give me a idea of the kind of stuff you need.

 

[Jacob J.]

Very interesting. I've seen NOS McCulloch gear drive sprockets in the original McPackaging. "Will fit all McCulloch gear drive chainsaws except 3-25, 4-30, 47, 49, 73, 77" (or similar wording) was printed on the packages. They probably can be used on those saws, even though they're not the "right" part. Do you happen to have any. 404-8 Homelite 1100/1130/3100G sprockets?

I'll have to look and see on the Homelite spurs. My 1130G has a 1/2" spur currently but I was lucky in that my 3100G came with the factory rim adapter. I read somewhere I think
that the 1130G stub shaft is the same diameter as a lot of Mac gear-drives.

 

[bplust]

While we're on the subject of drive gears, I have a new 1/2" one with two keyways, that fits 6-22, 7-21, 7-21C, 700G, 770G, 707G, 775G, and Super Whiz, and I have no use for it.

 

[rupedoggy]

You cats are old as dirt.

Old guys got as old as dirt by not becoming dirt. Young guys keep from becoming dirt by listening to old guys.

 

[nmurph]

Old guys got as old as dirt by not becoming dirt. Young guys keep from becoming dirt by listening to old guys.

Priceless!:msp_w00t::msp_w00t:

 

[Warped5]

Lookin' for air filter for Poulan 4200/4400/4900/5200/5400 in good shape. Have stuff to trade or ca$h. Please PM me, this thread moves pretty fast. Thanks!

 

[ptjeep]

I'm needing a crank/rod for a stihl 021. Found out the wrong way to remove the clutch anything in my sig is up for trade as well as cash. PM me if ya got something.

 

[67L36Driver]

Taiwan Mac MS354a needs a coil.

Anybody got one or a part number to look for or where to look?

Next door neighbor brought it over, no spark. Disconnected the ground wire and checked the flywheel gap. Saw is darn near new. Hate to throw it away.

We have old magnesium stuff to trade.

 

[Modifiedmark]

You cats are old as dirt.

Hello pot, this is kettle callin.

 

[Roanoker494]

Taiwan Mac MS354a needs a coil.

Anybody got one or a part number to look for or where to look?

Next door neighbor brought it over, no spark. Disconnected the ground wire and checked the flywheel gap. Saw is darn near new. Hate to throw it away.

We have old magnesium stuff to trade.

MTD 9288-310801
IGNITION ASS'Y

Listed as NLA, so are a lot of parts for the saw.
Parts and Diagrams for MTD MS354a 41AY54NQ077

EDIT:
Google search brings up several hits, looks like that coil is used on several models.
https://www.google.com/search?q="MT....,cf.osb&fp=d70c8e76b178f69e&biw=1366&bih=636

 

[67L36Driver]

Thanks Johnnie.

 

[epicklein22]

I'm needing a crank/rod for a stihl 021. Found out the wrong way to remove the clutch anything in my sig is up for trade as well as cash. PM me if ya got something.

I should have a good crank, what's the condition of the 1616 skil? I need a clutch drum and maybe an entire clutch assembly too.

 

[atvguns]

I am looking for part number 25, 29 and 30 for a 090 I have some green paper or a couple of parts saws to trade

Still needing these

 

[tbone75]

Looking for a 54mm P&C for a Makita 6401.Should have something you would like in trade? Edit: Going to try a AM BB kit on it? They can't be that bad? LOL

 

[Jacob J.]

Still needing these

You want me to see if we can get them through Stihl Northwest? I doubt those parts are that expensive.

 

[Warped5]

Looking for a 54mm P&C for a Makita 6401.Should have something you would like in trade?

Hiya John! You may want to PM Stumpy, he just took one out of a saw ...

 

[Jacob J.]

Hey guys- I'm looking for a full-wrap handle for Husky 394 or 395. It would probably be easiest for me to buy one but I do have a lot of stuff to trade. Thanks!

 

[Arrowhead]

I need a clutch assembly for a Plastic Mac Cat Eager Beaver boxstore type saw. I'll check the model number in a few... I'm thinking 2014??

Have a small mountain chain of parts 4 trade.

EDIT>>>> It's actually a MAC 3200. They made a bazillion of these under different names. This one is rare... it has spark and a non rotted primer bulb. :msp_w00t:

 

[Jacob J.]

EDIT>>>> It's actually a MAC 3200. They made a bazillion of these under different names. This one is rare... it has spark and a non rotted primer bulb. :msp_w00t:

Ed- I have one of those holding a tarp down on my firewood pile. I'll gladly give you the clutch off it and any other parts you need.