Shindaiwa 577 parts
Would whoever tried to PM me about the Shindaiwa 577 parts please try again? I emptied my mailbox. Thanks, Dan
Would whoever tried to PM me about the Shindaiwa 577 parts please try again? I emptied my mailbox. Thanks, Dan
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
PM sent.:msp_thumbup:
371 / 372 parts
Needing a few brake parts:
Brake Handle Actuator (503 00 87-01)
Small square Plunger (503 83 81-01)
Small Plunger Spring (503 43 65-01)
Brake handle
Any help would be appreciated, I have a few parts / bars and chain to trade.
Have a new OEM clutch cover for a Husqvarna 362.
Needing a few brake parts:
Brake Handle Actuator (503 00 87-01)
Small square Plunger (503 83 81-01)
Small Plunger Spring (503 43 65-01)
Brake handle
Any help would be appreciated, I have a few parts / bars and chain to trade.
Have a new OEM clutch cover for a Husqvarna 362.
Last edited:
tmessenger
ArboristSite Guru
Works both ways:
Actually I forgot to give you the Mac 35 when you were here last, Oh well I'll sneak it into your trunk next time you're down when you're not looking.
Looking for a Stihl cylinder and good piston for an 026. I have some parts/saws and or pictures of dead presidents.
And I'm STILL looking
Do you know what size you need? You might be able to cross over a husky or stihl one.
procarbine2k1
Addicted to ArboristSite
I would like to find a good, clean, used 7900 mahle cylinder. OEM piston would be fine too, but just figured I would end up going aftermarket. Cheaper the better, but I dont have any problem paying for a good cylinder. Looking to go on my 6421. I need a non cat muffler as well! Can trade green, part trade on a Total (Tsumura) 36" bar w/ decent chain or whatever else I might have that you want.
I'm needing an oil pump for a Jonny 2077/2083/Poulan Pro 475/505 if anyone can spare one. A good friend is rebuilding his big saw. I got cash and parts...Thanks...
Uncle Rico
ArboristSite Operative
Anyone interested in a Husqvarna 185CD? I picked one up locally to use on my mill occassionally and it's in pretty good shape. It fired right up and ran fine, seemed a little rich, has tons of compression. I haven't really checked it out yet but noticed some electrical tape on the handle and a broken tab on one of the fuel/oil caps.
I know they were only made for about a year so I thought I'd see if anyone was looking for one for their collection. I've posted a couple pics from the previous owner, I'll clean it up, check it out, and take some pics this evening or soon after. I thought I'd guage the interest before I start milling with it.
View attachment 242300
View attachment 242301
Send me a PM if you're interested, I'm always looking for cash, 7900 top end, alaskan mills/accessories, chain, etc.
I know they were only made for about a year so I thought I'd see if anyone was looking for one for their collection. I've posted a couple pics from the previous owner, I'll clean it up, check it out, and take some pics this evening or soon after. I thought I'd guage the interest before I start milling with it.
View attachment 242300
View attachment 242301
Send me a PM if you're interested, I'm always looking for cash, 7900 top end, alaskan mills/accessories, chain, etc.
nmurph
ArboristSite.com Sponsor
- Joined
- Nov 26, 2007
- Messages
- 16,162
- Reaction score
- 7,167
I have a NIB NWP BB if you are interested. $100 shipped.
Your request would work better if you have room in your Inbox.
Works both ways:
Actually I forgot to give you the Mac 35 when you were here last, Oh well I'll sneak it into your trunk next time you're down when you're not looking.
but what would i do with it since I don't have a boat that needs an anchor?
in all seriousness though... I need a jonsered throttle linkage part number 503 45 53-01 fits 625, 630, 630 super
got some stuff to trade or $$$...
Last edited:
I've got a 394 flywheel laying here needing a new home.
I've got a bing carb from an 064/066. I have an oil pump, fuel cap, oil cap, and 1 av buffer for 066/660.
I have a 10mm 044 cylinder with some light port work. No machine work has been done to it. I've never run it. I got it a few years back and never have tried it out on a saw. There's a small spike for 044/440, and older hd filter with the metal instead of plastic and a muffler front for a 440.
Looking for a nice 24" husky mount bar. Prefer .050" or .063" over .058" or green paper.
I can get pictures for any interested parties.
I've got a bing carb from an 064/066. I have an oil pump, fuel cap, oil cap, and 1 av buffer for 066/660.
I have a 10mm 044 cylinder with some light port work. No machine work has been done to it. I've never run it. I got it a few years back and never have tried it out on a saw. There's a small spike for 044/440, and older hd filter with the metal instead of plastic and a muffler front for a 440.
Looking for a nice 24" husky mount bar. Prefer .050" or .063" over .058" or green paper.
I can get pictures for any interested parties.
but what would i do with it since I don't have a boat that needs an anchor?
in all seriousness though... I need a jonsered throttle linkage part number 503 45 53-01 fits 625, 630, 630 super
got some stuff to trade or $$$...
I can't reply to your PM because your Inbox is full!
But to answer your question, i don't know but I'd ask in the Jonsered thread.
edited
Mastermind
Work Saw Specialist
I still have a 266xp that's a good runner. I also have a really nice 028 Super that has a new rim drive setup. Both saws have been taken down for cleaning and inspection. Sell or trade.
parrisw
Tree Freak
I think JJ is looking for a flywheel for a 394. Check with him.
did any of you guys happen to see that mitch (mweba) put his homelite 8800 on local craigslist for $400... :msp_w00t::msp_w00t::msp_w00t:
decent deal if you need a 80-90cc saw!!!!
Homelite 8800 chainsaw
wendel sorry about that inbox issue... I have it cleaned out now! thanks for letting me know!
decent deal if you need a 80-90cc saw!!!!
Homelite 8800 chainsaw
wendel sorry about that inbox issue... I have it cleaned out now! thanks for letting me know!
