Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I need a Mall 7 clucth I have the clucth drum on bar but no clucth itself. Can any body help me find a mall model 7 clucth? Thank you for your help.
 
I have a McCulloch 600 that I'm gonna part out. It runs strong, and the b/c are in great shape, but the chain brake is a pain and this morning the recoil starter quit rewinding so she needs to go. I am looking for a 16" bar and chain for my stihl 028 super. Let me know what ya got.. Would consider anything..

Thanks.!!


BRO's iPhone
 
Anyone interested in this:
42575541-f0b6-4412.jpg

42575541-f0cd-4867.jpg
 
Looking to trade some of these off for some modern reliability. I have a little firewood business going quite well on the side and would like to slim down the "vintage/project saws" and trade them in for some modern work saws.

This would be the place to make that happen.

I would be interested in more modern saws, in the 50-80cc range, that are pretty much ready to go. Take one, take all. Trades and nasty green are all welcome forms of "trade meat"

All saws are powerheads only, and I will do my best to accurately describe each.

First off, McCulloch CP70, needs a few hardware bits, and will run, but possibly leaking a little air. This saw is in overall nice condition and appears to be complete. I installed a new intake boot. Piston and cylinder are in good shape, excellent compression. It will need the correct throttle trigger, the one on it is not correct for the throttle interlock. This one of the saws used in "Sometimes A Great Notion." Check out the nice full wrap. Has DSP valve instead of the poppet type decomp.

53e5b5e3.jpg

fe7f96d4.jpg

d4280502.jpg

aa9c168a.jpg



McCulloch SP60, overall good shape, has spark and compression, clean. Needs some work to make run properly. Could use a new fuel line. Has a crack in the clutch cover.
2d056214.jpg

a9da64cf.jpg


J-red 49sp, good runner, excellent compression, complete. Has a short rope. Muffler has been opened up. Adding a deflector wouldn't hurt it any.

cfda18af.jpg

23759321.jpg



Drop me a PM if you have any interest in any of these, please don't PM me if you have 3 Homelite XLs and a Poulan 1.8 motor you would like to trade for them.

Thanks,

Chris
 
Also up for trade....


A really nice McCulloch 7-10. Great runner, very powerful. Overall very nice shape, shouldn't need a single thing. This saw here is an earlier variation of a PM700, with some minor differences, as well as believed to have a little hotter porting inside the motor.

c1a092ed.jpg

fc1dd182.jpg

9fe24496.jpg



Here is the PM850.....This saw runs great, just needs one part that I haven't gotten around to. The bar oiler leaks a little oil into the crankcase when you use the manual oiler. The gasket is a buck, and it takes 1 screw, one bolt and all of about 5 minutes to replace. Has a basically new McCulloch 28" bar with Carlton chisel chain. AV mounts as getting a bit worn, so you may want to replace them down the line. Other than that, a great saw. You may own it, still doesn't make you half the badas* RandyMac is.

a0384734.jpg

77709d50.jpg

1c5329d6.jpg

966e4949.jpg


Chris
 
I need a upper av mount for an 084.....I've exhausted all other avenues. :(

PM me with details.
I have some NOS 084 AV mounts.


Mike

Was you able to cover this Mike?

Reason I ask I was searching for some stihl stuff today and came across upper right used AV mount that is still usable with a little crack in rubber. I had replaced all 4 on my 4 084's back in the day with new ones.

Also found a new 066 one and and a used 066 one with crack in rubber.
 
Was you able to cover this Mike?

Reason I ask I was searching for some stihl stuff today and came across upper right used AV mount that is still usable with a little crack in rubber. I had replaced all 4 on my 4 084's back in the day with new ones.

Also found a new 066 one and and a used 066 one with crack in rubber.

I have one in route K.

Thanks for looking out for me. :)
 

Latest posts

Back
Top