Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I wanted to do a 440/460 hybrid, but the parts seem to be going for amounts off the chart.
I may play with 044 #2, do a gasket delete and timing advance and see what happens.
I may play with 044 #2, do a gasket delete and timing advance and see what happens.
SHINDAIWA REPAIR GUYS
Shindaiwa chainsaws "BETTER THEN ALL".
I done a few stihl's did a 361 runs like it's on fire.
I have no idea y that model goes for so much and there's no reason.
I know ebay has pushed the price of junk to a new level.
I have no idea y that model goes for so much and there's no reason.
I know ebay has pushed the price of junk to a new level.
Freakingstang
Doctor Freakinstein
I've still got my 064 apart... then I want to finish my 380xp hybrid that I started years ago. (372 bottom end, 385 jug). Seems like the house takes up all my free time these days, then struggling to get wood ahead, then..... then.... it never ends
yeah no ****.. they used to be cheap... smashed logger 460/046 for 100 bucks... another 100 bucks for a burnt p/c 044... you were in it 2 bills or less and part of the fun was the conversion.... but 5,6 to even 700 dollar parts saw plus time and more parts and porting... no thanks.
#2 should run good. base gasket delete, drop the intake a smidgin and raise the exhaust the thickness of the gasket. It'll run good. or you could rasp file the piston so the jug isn't permanently altered incase you wanted to send it off down the road, then don't touch the exhaust.
yeah no ****.. they used to be cheap... smashed logger 460/046 for 100 bucks... another 100 bucks for a burnt p/c 044... you were in it 2 bills or less and part of the fun was the conversion.... but 5,6 to even 700 dollar parts saw plus time and more parts and porting... no thanks.
#2 should run good. base gasket delete, drop the intake a smidgin and raise the exhaust the thickness of the gasket. It'll run good. or you could rasp file the piston so the jug isn't permanently altered incase you wanted to send it off down the road, then don't touch the exhaust.
Not many yet.... still focused on the farm... if some calves get sold....
BUT on the bench:
Jonsered 2083 needs top end... going to try and salvage what's there and add a new piston.
Husqvarna 298 All there, needs a good cleaning and a carb kit. May need oil lines to chain oiler.
Husqvarna 385 needs new top end.
Husqvarna 372 "Stock" build for a friend. Have all the parts.. just need time.
Another tweaked 350, this time with a turned squish band and port timing like the "fugly's" (with lower exhaust than fugly one, more along the lines of 103 ATDC & blow down around 18 degrees)
A 372 with "Huztl" 52mm top end stuffed with a Stihl 064 piston with the crown trimmed ... effectively a pop up piston. Has a shorter skirt. Intake will be a little too advanced at 81 BTDC.
A 365 going to get a OEM 372xpw top end, the 75cc one. No mods at first.
That's it until spring time.
Other projects on the shelf but not budgeted time or parts yet include:
A clean L65. Needs rubber parts and a ring.
562... research project. Going to get some lathe work.
357 research project going to get a cut squish band & timing changed.
Several more 350's & 372's.. most sold when they are done. All with lathe work.
Homelite XP1000... needs a lot. All the parts are there. typical barn find.
Husqvarna 55, needed a piston put in (Have everything but time)
Husqvarna 42 needs a few odds and ends...
Two Jonsered 625's going to evolve into 272's
BUT on the bench:
Jonsered 2083 needs top end... going to try and salvage what's there and add a new piston.
Husqvarna 298 All there, needs a good cleaning and a carb kit. May need oil lines to chain oiler.
Husqvarna 385 needs new top end.
Husqvarna 372 "Stock" build for a friend. Have all the parts.. just need time.
Another tweaked 350, this time with a turned squish band and port timing like the "fugly's" (with lower exhaust than fugly one, more along the lines of 103 ATDC & blow down around 18 degrees)
A 372 with "Huztl" 52mm top end stuffed with a Stihl 064 piston with the crown trimmed ... effectively a pop up piston. Has a shorter skirt. Intake will be a little too advanced at 81 BTDC.
A 365 going to get a OEM 372xpw top end, the 75cc one. No mods at first.
That's it until spring time.
Other projects on the shelf but not budgeted time or parts yet include:
A clean L65. Needs rubber parts and a ring.
562... research project. Going to get some lathe work.
357 research project going to get a cut squish band & timing changed.
Several more 350's & 372's.. most sold when they are done. All with lathe work.
Homelite XP1000... needs a lot. All the parts are there. typical barn find.
Husqvarna 55, needed a piston put in (Have everything but time)
Husqvarna 42 needs a few odds and ends...
Two Jonsered 625's going to evolve into 272's
SHINDAIWA REPAIR GUYS
Shindaiwa chainsaws "BETTER THEN ALL".
have a 910 johnsered with a 199 carb on it sounds nice ( so husky )
poor handle grip mabey impulse and carb work, dies off under load
poor handle grip mabey impulse and carb work, dies off under load
jeepyfz450
Addicted to ArboristSite
I have lots of saw projects with no time to build them.....
A 3120 that needs a crank
066 that needs a top end
Çr 125 that I want to build into another bikesaw.
The list goes on and on
A 3120 that needs a crank
066 that needs a top end
Çr 125 that I want to build into another bikesaw.
The list goes on and on
Big_Wood
westcoast dweller
looking for a decent 281xp top cover. high top for the HD filter would be real cool
Bump. can be ugly as sin. just no cracks would be nice.
nmurph
ArboristSite.com Sponsor
- Joined
- Nov 26, 2007
- Messages
- 16,162
- Reaction score
- 7,167
Would this work?Bump. can be ugly as sin. just no cracks would be nice.
It will need the bolts. There are only two in it and they are socket caps.
Big_Wood
westcoast dweller
PM sent Neal. Thanks bud
Duke Thieroff
Fill your hands, you SOB!
I believe I have a kill switch Josh.
Might be able to drop it in with the cylinder kit.
Might be able to drop it in with the cylinder kit.
Chris_In_VT
Brrraaaaap!
Man, all you guys with too many projects and not enough time...
I've got the opposite problem! Plenty of time this winter, but I have nothing lined up for the bench!
(shameless beg)
I got a running husky 55 I'd swap for a good husky project saw...
I've got the opposite problem! Plenty of time this winter, but I have nothing lined up for the bench!
(shameless beg)
I got a running husky 55 I'd swap for a good husky project saw...
Chris_In_VT
Brrraaaaap!
Not that beggars can be choosers....
But I was thinking more along the lines of a complete saw, in decent shape maybe needing a top end or bottom end rebuild.
shorthunter
ArboristSite Guru
Gonna put a Dolmar 115i cylinder on a 113
SHINDAIWA REPAIR GUYS
Shindaiwa chainsaws "BETTER THEN ALL".
So you got that 55 going and so I have to ask what was you thinking on that 500 its so clean and im thinking that museum thing could be the ticket the house of Shindaiwa what do you think.
Big_Wood
westcoast dweller
yer in the wrong place guy. move over and start your own thread in the trader. will get way more hits over there.
I need a coil for a 394/395.
Similar threads
