FarmerTec Huztl MS660 Updated Build Kit - Build Thread

[Keaton85]

Finally got around to starting my kit, and it’s been as expected so far.

To add to the list of “to-dos” is flushing the crank bearings out!! I had a lot of metal in the bearings from the block assembly. I used electrical connection spray cleaner. Flushing over a clean cloth to find when metal flakes stopped coming out.

I only use electrical connection cleaner since it doesn’t eat the lip seals. Anyway, my two cents!

 

[CsClimbr]

What the hell did I get myself into? “Some assembly required”

Perfect manly puzzle, no instructions cause we don’t read them anyway.

I plan to run it first, troubleshoot later.

 

[MG porting]

What the hell did I get myself into? “Some assembly required”

Perfect manly puzzle, no instructions cause we don’t read them anyway.

I plan to run it first, troubleshoot later.

View attachment 651688

Looks like your getting there.

 

[CsClimbr]

Looks like your getting there.

I’m getting somewhere, no clue where but somewhere

I have no expectations with this thing, I’ll be surprised if it even pops lol

 

[MG porting]

I’m getting somewhere, no clue where but somewhere

I have no expectations with this thing, I’ll be surprised if it even pops lol

It will run just take your time it's not like your inventing the wheel Lol. Just my being funny.

 

[CsClimbr]

It will run just take your time it's not like your inventing the wheel Lol. Just my being funny.

I think I screwed up already. Was I supposed to mount that oil pump first, I remember reading somethin’

That crank ain’t turning real freely.. worries me. Not rubbing on either side but it’s tight even prior to any top end parts. I think a bearing is no good. Was I supposed to go OEM with them? Maybe I’m the problem, usually am

 

[MG porting]

I think I screwed up already. Was I supposed to mount that oil pump first, I remember reading somethin’

That crank ain’t turning real freely.. worries me. Not rubbing on either side but it’s tight even prior to any top end parts. I think a bearing is no good. Was I supposed to go OEM with them? Maybe I’m the problem, usually am

Oil pump first and then worm gear then big clutch washer then clutch and clutch drum and baring then spergear then retaining washer and eclip.

 

[MG porting]

I think I screwed up already. Was I supposed to mount that oil pump first, I remember reading somethin’

That crank ain’t turning real freely.. worries me. Not rubbing on either side but it’s tight even prior to any top end parts. I think a bearing is no good. Was I supposed to go OEM with them? Maybe I’m the problem, usually am

And did you put oil in the crank case on the bearings.

 

[CsClimbr]

Yup, everything on point. Maybe it just me, seems a little tough to turn but this a lil’ bigger than my 200 I just set aside to open this can of worms

 

[MG porting]

Yup, everything on point. Maybe it just me, seems a little tough to turn but this a lil’ bigger than my 200 I just set aside to open this can of worms

Lol. You'll be surprised how good you can make it run but that's up to you on that part spend the money where it counts on these things and they will run strong.

 

[CsClimbr]

Well that was fun, I’d like to give it a yank but the ole lady and sleeping baby upstairs might not be as appreciative

Tomorrow I shall go thru the bag of left overs

 

[golddredgergold]

Thats the part that got me was the leftovers. Felt like I forgot something. But it was all doubles of parts. So no worries. Love my 660 bad ass saw. No issues with mine thus far.

 

[golddredgergold]

Bedford you there? You been way to quiet. Hope all is well.

 

[MG porting]

Well that was fun, I’d like to give it a yank but the ole lady and sleeping baby upstairs might not be as appreciative

Tomorrow I shall go thru the bag of left overs

View attachment 651704

I see you have a ms440 there she's going to be jealous. Lol

 

[MG porting]

Bedford you there? You been way to quiet. Hope all is well.

He posted a video on YouTube this morning so I think he's getting reddy for another project maybe.

 

[CsClimbr]

I see you have a ms440 there she's going to be jealous. Lol

She arrived yesterday about an hour prior to the Farmertec. Got her off the tradin’ post

 

[MG porting]

She arrived yesterday about an hour prior to the Farmertec. Got her off the tradin’ post

Nice I wish I never sold my 044 and my ms440 they both were great runners.

 

[CsClimbr]

Nice I wish I never sold my 044 and my ms440 they both were great runners.

I’ve never run one, gotta get a bar on it. It’s an 044 mag but I’m not familiar with any differences between an 044 and 440.. I assume very much alike?

 

[MG porting]

I’ve never run one, gotta get a bar on it. It’s an 044 mag but I’m not familiar with any differences between an 044 and 440.. I assume very much alike?

That's easy the 044 would be my first choice. Lol

 

[golddredgergold]

Hey do you guys know when huztl ships from china with SF Express do they transfer to the mail or ups for delivery or who actually brings it to my door?