stihl

I blew up my ms290 and need a rebuild kit. People are saying make it a 390 with a slightly bigger kit that will fit. Are there any drawbacks of getting the 49mm kit as opposed to the 46mm kit. Do I need any additional parts? Ps. My mechanic is doing it. Thanks

Powerhead only. 026 black switch in great running order. A little bit ugly. Has some scuffs where a guy decided to carve his name into the saw, I sanded that off. I went through the carb and blew out the filter. Has a 325 sprocket on it. Has been running excellent. Oils like crazy. I have...

Hi there just wanted to get some opinions about what’s a decent price for a good running 090? The top end was rebuilt with oe parts a few years back, has one small repair weld on lower handle. Come with like new 41” stihl bar. I see prices all over the place for these things. 3k - 1k ?? It’s a...

Hi there just wanted to get some opinions about what’s a decent price for a good running 090? The top end was rebuilt with oe parts a few years back, has one small repair weld on lower handle. Come with like new 41” stihl bar. I see prices all over the place for these things. 3k - 1k ?? It’s a...

Hi there! listing my Stihl 084 for sale. the saw runs and cuts excellently. This 122cc torque-monster has great compression and overall is in very nice condition. the saw comes with a Maxflow air filter, Pro-safety full wrap handle, and 36 inch Stihl ES bar. also included in the sale are two...

After rebuilding this turd saw from 2 different saws a ms260 and 026 i kept it mostly with 026 parts except 1 case half, so after bunch of testing and working up in steps to porting this 026 (48.7cc model) After not satisfied turning a 16 inch with 325 i start to port this saw I was on...

I have several Stihl 026 chainsaws For sale. All excellent used condition. All excellent compression 160-165psi. Most are later fixed H carburetors. I have gone through a few and replaced some lines and filters a a couple of the carbs with aftermarket fully adjustable carbs. I will include...

Have a 201t that I keep having bounding up issues with. Have put a new chain, bar and clutch on so far and still having the issue. Will run freely as it should for awhile and then all of a sudden seize up and I have to loosen the bar to free it up. No plastic or guard damage so I’m not sure...

I have a few more saws we are parting out along with some other small parts Offering parts only, no complete saws will be sold, MS261C Running Saw Has tank damage all other parts check out MS661C Heavy Damage but many small parts left good engine, MS200T Crankcase and a few parts...

I need a new pole pruner for our orchard of mostly cherry trees on 30 acres, it needs to reach to about 5.5m high (while being held). I've had several professionals recommending different conflicting setups, those being: Stihl HTA-135 pole pruner Stihl HTA-86 pole pruner KMA-135 R KombiSystem...

I just picked up a free 028 WB. Going to replace the AV bushings and I take boot. I would like to find a shop manual to down load and parts list. Is there any thing else I should look for or be aware of??

Does anyone know of a saw builder that cuts a groove in their rings??

So I decided to get around to pulling the carb on a nice 011 that I picked up awhile back, in order to clean the carb out and give it a new diaphragm, which I'm fairly certain is all this saw really needs to make it good as new. Cleaning and reassembly of the carb went just fine. The old...

So I don’t know a lot about these saws. I was thinking of a nice old school 044? Just always wanted one. But should I pick up a 044 or 440? Is the power and weight about the same? Is there one advantage over the other?? Thanks!

Heya folks, Got this used ms250 up and running, but still can’t get it in good working condition. Bought it a new bar and chain and using stihl oil to rule out those variables. I’m certain my chain isn’t too tight as I can pull it up enough to reveal the drive link. The chain, however, feels...

I have these saws being parted out this week, Many good parts available, Husqvarna 575Xp Husqvarna T435 Husqvarna 562XP Husqvarna 350 Echo CS-590 Echo CS-355T Stihl MS270C Stihl 034 Av Stihl MS461 Stihl 038 AV Stihl 026 Stihl 031 Stihl 039 029 All Parts are covered under a 30 hassle...

So I was looking to buy an MS 381 and I notice someone was selling this, note that in the bottom sticker and in the accesories it says it is an MS 660.

scored the piston on my dads 391 the other day while milling, saw went way down on power then just died I havent pulled the cylinder off yet, but im just wondering, how much damage do yall think there will be? and could it be honed out and just put a new piston in? exhaust side of the piston...

Sold a Stihl 661c on the bay last week, buyer messages me yesterday saying we have a problem. Buyer says he took it in to get it serviced and they told him that the “case for the bar threads are cracked and the bar bolt is cracked” I didn’t even clean this saw before selling it, so I’ll just...

I have a couple projects for sale. I'll separate them by replys:. First is a Stihl 031AV electronic. I completely tore this saw down. Cleaned it, reassembled and tried to get it running well. The ignition module(S) i have are shot. I had to install a nova ignition module in it to get it to run...