What in the world is this???!!! MS661 related.

[pro94lt]

someone needs to test to see how much the stihl factory installed restrictor restricts...

 

[singinwoodwackr]

R50 is pretty clean stuff.......Super Techniplate on the other hand is nasty.

ah, so bought the wrong Klotz...crap...

 

[Deleted member 83629]

well sorry for stating inaccurate information it i always heard from people with 2 stroke bikes it burned dirty.
i guess they were running the castor or the super.

 

[boxygen]

Pardon my ignorance, but what does the computer saw if you "hook it up"? You would think mtronic would recognize this as a problem and log it as such.

 

[showrguy]

Pardon my ignorance, but what does the computer saw if you "hook it up"? You would think mtronic would recognize this as a problem and log it as such.

You shuddup,
This is now an oil thread..

 

[Mastermind]

You shuddup,
This is now an oil thread..

Repped

 

[nmurph]

Oil thread and doughnut thread, all packed into one.

 

[CR500]

I like to wear a little R50 when I go out.... has not worked sadly

Sent from my non internal combustion device.

 

[blsnelling]

K2 and H1-R are my two favorite oils.

 

[jughead500]

Hmmm sphincter effect.

 

[Mastermind]

K2 and H1-R are my two favorite oils.

Same here.

The K2 smells bad to me though.........but most folks tell me the H1R smells bad. I can't smell it at all.

 

[singinwoodwackr]

K2 and H1-R are my two favorite oils.

so, flip a coin?

 

[mdavlee]

would running premium gas rather than regular make a difference in deposits?
Klotz Super Techniplate at 32:1 I've been running this in all my saws for a couple years now and never seen anything like this buildup.
So, which of the above suggested synthetics should I go to? price/gal seems about the same with freight via Amazon.
the mystery continues...

If the saws get run hard and not a ton of idle time I don't see deposits that much. If they are run on a mill and only idle a minute or so after a cut and shut off I've not got a totally black piston top even with Maxima 927. H1R takes too much adjustment for me to run and then try to send a saw out to someone who doesn't have a tach to tune them. I've noticed almost a 1k rpm difference from Klotz to H1R. K2 is good oil as is Motul 800. The Motul 800 can be used to =54° according to the engineers I spoke with back in December.

 

[Dieselshawn]

Since I have those rubber rings in the intake, I should try the saw on the dyno and see what difference it makes.

At first i couldn't figure out where the rubber came from as one was on the floor and the other was sideways in the intake port of the cylinder, not the boot.

I asked randy but he was confused too until he sent the link to this post.

I've been asked to get the serial number of the 661 to compare.

Just waiting to get home from work.

 

[singinwoodwackr]

If the saws get run hard and not a ton of idle time I don't see deposits that much. If they are run on a mill and only idle a minute or so after a cut and shut off I've not got a totally black piston top even with Maxima 927. H1R takes too much adjustment for me to run and then try to send a saw out to someone who doesn't have a tach to tune them. I've noticed almost a 1k rpm difference from Klotz to H1R. K2 is good oil as is Motul 800. The Motul 800 can be used to =54° according to the engineers I spoke with back in December.

hmm, I wonder which way to go with this auto-tune system. obviously the stuff I've been using ain't workin'.

 

[Roll Tide]

I guess I'm the only guy that's stuck with Stihl Ultra.

 

[singinwoodwackr]

Since I have those rubber rings in the intake, I should try the saw on the dyno and see what difference it makes.

At first i couldn't figure out where the rubber came from as one was on the floor and the other was sideways in the intake port of the cylinder, not the boot.

I asked randy but he was confused too until he sent the link to this post.

I've been asked to get the serial number of the 661 to compare.

Just waiting to get home from work.

this one is: 179211553 MS661RCM
bought from: https://sharpeningshop.stihldealer.net/ Turlock, Calif
I've been buying saws, etc from these guys since the late '80s and Mike and his bunch are great to work with...I highly recommend them.

 

[mdavlee]

hmm, I wonder which way to go with this auto-tune system. obviously the stuff I've been using ain't workin'.

I haven't noticed any problems with R50, k2, or Motul 800 with the huskies and one 441 that was here.

 

[nmurph]

I guess I'm the only guy that's stuck with Stihl Ultra.

That's all I use.

 

[Roll Tide]

QUOTE="nmurph, post: 5253240, member: 18671"]That's all I use.[/QUOTE]
Thats all I've ever run.