Search results

XL923 VI944 cylinder Can someone tell me if a VI944 cylinder would fit on a XL923? Exhaust ports are the same, but for some reason i'm not so sure ...

I got 2 blind end bearings with the new piston and rings kit, one side is allready installed. With the worn piston i could not tap the pin out, the piston eventualy splitted in half and then i could remove the pin. Also the worn piston has no markings. The rings can actually be moved in any...

Just got a new piston for my Mcculloch PM6 i'm restoring. The one side of the piston has a "P" marked on it, the other side says nothing. So does the marked side supposed to be installed at the clutch side or the flywheel side of the saw?

I run Stihl "Motomix" (premixed fuel) at 50:1 for my ms290 ... For my older saws i just add more oil (HP Ultra) to the premixed fuel at 32:1

Thanks man, i was planning to use a tachometer to tune them. I started adjusting the XL923 yesterday, both needles 1 - 1/4 turns out to start and warmed her up for a couple of minutes. After leaning out a little she ran fine, but if i cut aut piece of wood at WOT she starts bogging and shuts of...

XL923 SXL925 stock RPM's Can someone tell me the stock rpm's for the XL923 and SXL925?

I love mine because it has lots of power for it's size. Maybe a 12" or 14" bar will be better for the bigger stuff, also remember to keep the chain sharp;) Good luck!

Yes, i do Full choke until she pops, then fast idle for a bout 10 seconds, blip the throttle and let her idle for a while. Also before i put the saw into wood i usualy go slowly from half throttle to full throttle, and after that it's WOT all the way ...

Strange, than you will also know it s:censored:cks pretty much comming home and realize it just won't fit. Maybe a little off topic, but has anyone muffler modded one of these small XL's before? I was thinking of opening the muffler just a little bit and richen the L adjuster a little, they...

Thanks, i know lol, have been reading Madsen's link, i realy learned a lot more by reading it:) :cheers:

The drive links only have some sort of logo stamped, the parts that go into the bar groves are damaged and unreadable probably because the oiler did not work.

Indeed, if i'm right i will be needing a 3/8" .050 guage chain. The bar recommended .375 pitch on the package, if i only knew that was the same as 3/8" when i was standing there at the store ... lol Just good i bought one of the cheapest ones.

I think it does, not realy sure, the drive sprocket also fits the bigger Stihl 3/8" as well as the small old chain wich came with the saw. The chain package sais: .325 pitch, .050 guage, will check later for the No of drive links. The original old chain is defenetly low profile, the pitch i...

Thanks a lot for the info people! I checked for numbers but there weren't any:confused: So 3/8" would be the right chain? The bar sais .375 on it and the gauge should be .050"/1,3mm Thanks for the link, i'll check it right now:cheers:

Hi all, First of all i'm a noob when it comes to chain types. Whent to the hardware store today for a new bar and chain for my XL, i don't want to put to much money in that saw, that's the reason i whent to the hardware store. When i was back at home i realized the chain didn't fit the...

I'm working on one of those right now, i think they are very easy to work on, probably because it's the only saw i ever worked on. Mine runs and cuts wood but the oiler does not work. I'm going to put a new fuel line, oiler lines, duckbil valve, fuel filter and air filter on. Just waiting for...

I would look for a 20" rollomatic ES, i don't know about the duromatic but i don't think they would fit on the 391

So i guess buying the baffle is the best thing to do? I already have the spark arrester on mine, my previous XL did not have anything in the muffler, probably the reason why it never ran right ... And she does runs pretty loud for a saw that small

When looking to buy new parts for my Homey XL on ebay i came across this: That metal sheet would be a spark arrestor screen for the muffler, this is my second XL i own and neither of them had this part in the muffler:dizzy: So i'm wondering ... would it need this part?