Search results

Hello! I wonder if there are any possible advantages with a richer than "nominal" oil-to-fuel-mixture such as, e.g., 3% instead of 2%. I seem to have understood that some people use richer mixture (including myself) but now I am wondering what the possible (if any) advantages are? I sort of...

So - I have bought a 10 year or so old "toasted" Husky 357xp for very little just to have something to pretend I am a mecha- nic a little with ... . Now when I am hoping saw is getting ready for use I was thin- king of changing the clutch drum to a Oregon 108565X with a large sprocket fit in...

I tripped over this scientific (?) report on "Long Term Repair and Maintenance Cost of some Professional Chainsaws" ...

Hello! Do you sell "Pressure vacuum tester for Husky" OEM 531 03 06-23? Best

Hello! My oldest 346xp (a 2010 - I have two 2011 as well) has a problem - it seems clear it gets too much air - which makes it necessary to choke it excessively in order to make it start - after that one must more or less have it throttled all the time to make it "stay alive" - and in doing so...

Hello! I have one Husky 42 inch hard nose bar already, but happened to come over another new/unused one for virtually no money, although I do not really need it - so my plan was/is to shorten it to 36 inch or so :) ... . Not the most usual chain saw repair activity I guess - anyway I was...

Hallo! Which carburetor for Hva 346xp? I have one 2010 and two 2011 - NE of course - all three were bought from the US - preferably I want a carburetor that fits all three (if there is a difference) ... . When I look at ebay.com and elsewere it seems that both Za- ma C3-EL18B and C3-EL32 are...

One of my 346xp's has started to behave strange recently - it needs 20 or so pulls to start - it just ignites and then dies - until 20 or so pulls, that is - and when it finally starts and gets worm it has a way too high idle rev so that the chain never stops - albeit it is quite firmly...

Here are a few new cut birches Here are a few new cut oak trees (20 and 30 inches respectively) And then finally a medium (for Sweden at least) pine leaning backwards against an invisible (on the picture) house as well as siedewise to the left towards the visilble buildings ...

Today - as it was raining outside - I finally changed the handle of my little one-hand sledge hammer which I use both for wood shopping and for hit- ting wedges at tree felling ... . As I need this little guy a lot I have ben hes- itating to change the handle, but today it happened ... . I...

I just bought around 300DL of Oregon (historic) 50C 0.404 0.050 (chain- saw) chain with tie straps and presets for around USD170 (incl ship) - new, that is, but still old :) . Was that stupid or ingenious? (Well - I know I can make use of it, so what I am really asking I suppose is if what the...

Look here - I put a 68DL 1/2 inch Oregon 31C3 chain on an 395xp with 28" blade - looks and feels much better that the measly 92DL 3/8 chain the saw came with :) :

Picked up this new unused (from a big buidling project who didn't needed it) 120 cc petrol cutting machine for GBP 540 - cirka USD 750 I guess - on ebay.uk ... . It is a bad ass machine as compared with eletric cutters / angle grinders. If the cutting disc looks a bit ragid it is because...

Who sells 15/64 (6.0 mm) diameter chain saw files? (I know Vallorbe makes them but they seem to be impossible to buy for me although I have tried to get them through contacting Vallorbe, getting redirected etc ... (: .) So, who sells 15/64 (6.0 mm) diam chain saw files? PS. Is there a...

What chain brand is this 3/8 LP chain? Picked a few of them up on Ebay beliving I was buying Stihl chains but that was because I didn't read add good enough :) :) :) . Anyway - what are they? (Seem to recognize them, but can- not remember from where ... .)

Hello! Where do I find 1/2 inch chainsaw chains (not wider than 0.063)? I do not mind chain reels if available ... . Also, I have been told that there should be 7/16 chains available - where do I find them? Thanks

Hello! I am wondering what bar and sprocket/rim I can use to run 0.325 0.050 chain and say a 14" bar on Stihl 020 and/or MS200? (Oregon number please :) ... .) Saws will be used only to very tiny stuff so I imagine they should cope well with 0.325 :) ... . Thanks

I was wondering about a fast cutting .404 .058 chain? (It would be used on 20-24 bars, possibly with "enlarged" drive sprocket ... .) Perhaps Oregon 58CL?

Hello! I was wondering about good chain making tools ... . At present I use Oregon Italian made spinner and breaker for USD 150 or so (Oregon's chepest stuff) but was thinking of investing in something more "high-end" as I have ended up making all chain sizes myself from reels ... ...

Hello! I wonder about drive link counts for chain saws: Specifically that they can vary just a little (one drive link or so) between different bars of same claimed length for a given saw ... . For example, I was planning to use an Oregon 28 inch Laser Tip solid 3/8 bar for 92 drive...