Mastermind meets the NE346XP
- Thread starter Mastermind
- Start date
Help Support Arborist Forum:
SawTroll
Information Collector
I rep both of you as often as I can anyway, so there are no room for extra rep.....:too_sad:
With the same fuel that we run in the build-off saws!
wigglesworth
Booned
I'll be bringing a bone stock 346xp to terrys. In case anybody cares to see how much faster there 346 is than a stock one 
well, it's muffler is opened up, but that's it....
well, it's muffler is opened up, but that's it....
Mastermind
Work Saw Specialist
Here's the little 346 handing a whooping to my 026. The 026 has a better chain too.
[video=youtube;za4B49510Gg]http://www.youtube.com/watch?v=za4B49510Gg[/video]
[video=youtube;za4B49510Gg]http://www.youtube.com/watch?v=za4B49510Gg[/video]
Last edited:
I can't believe the SOB owner didn't send you a better chain. What a putz.
Hedgerow
HACK
3-seconds difference... Got a strong runner there... Those 346's are kinda special ain't they...
I'll be bringing a bone stock 346xp to terrys. In case anybody cares to see how much faster there 346 is than a stock one
ill have my bonestock ms261 we can compare it too also. 2 MORE DAYS!!!!!
if i can come up with a good gas carb for it i will try and get it going. dont know that ill have time to get a carb kit picked up and installed in it. or if i even have a good gas carb to put on it. it uses a wj69 on gas, its a thirsty little fella :msp_sneaky:
The truck is loaded and ready to pull out. I'll pick up the 441 and 576 at Niks on the way out of Cincy tomorrow.
i sent my 044 alky carb to logging22 i have a wj69 drilled for alky but havent dont the carving to get it in there yet. i built one saw for a member tonight and didnt get to the 026. if i have time tommorrow evening ill try to get it in there. it should be a good runner with it
Randy, the 346 is amazing!! Everyone at the Iowa GTG was very impressed.
And yes, the 3/8's was fastest by a second over the .325 7 pin. I think it could even handle a 3/8's 8 pin.
I will get videos linked as soon as Mitch gets them posted.
And yes, the 3/8's was fastest by a second over the .325 7 pin. I think it could even handle a 3/8's 8 pin.
I will get videos linked as soon as Mitch gets them posted.
wigglesworth
Booned
Mastermind
Work Saw Specialist
I hoped you would enjoy that saw my friend. When I build saws for guys (like yourself) that have had the opportunity to run some fast saws I always hope they will measure up. I can breathe now.
Several there who would know said it is the strongest 50 cc saw they have ever seen. 
Walnut
(videos may not match the posted times)
.325 7 pin 9.93 seconds
[video=youtube;CpNlF7SBgLA]http://www.youtube.com/watch?v=CpNlF7SBgLA&feature=uploademail[/video]
.325 8 pin 9.60 seconds
[video=youtube;H9Q6ggtO6Qk]http://www.youtube.com/watch?v=H9Q6ggtO6Qk&feature=uploademail[/video]
3/8's 7 pin 8.93 on second run
[video=youtube;jlbQRtjzXE4]http://www.youtube.com/watch?v=jlbQRtjzXE4&feature=channel_video_title[/video]
(videos may not match the posted times)
.325 7 pin 9.93 seconds
[video=youtube;CpNlF7SBgLA]http://www.youtube.com/watch?v=CpNlF7SBgLA&feature=uploademail[/video]
.325 8 pin 9.60 seconds
[video=youtube;H9Q6ggtO6Qk]http://www.youtube.com/watch?v=H9Q6ggtO6Qk&feature=uploademail[/video]
3/8's 7 pin 8.93 on second run
[video=youtube;jlbQRtjzXE4]http://www.youtube.com/watch?v=jlbQRtjzXE4&feature=channel_video_title[/video]
Mastermind
Work Saw Specialist
It does, doesn't it?
Mastermind
Work Saw Specialist
I'm planning a build of my own on one of those saws. To be honest, that one of yours got me to wanting one.......bad. :msp_ohmy:
