Search results

Found this today while browsing the UK website http://hqendurance.azurewebsites.net/?utm_source=husqvarna.com&utm_medium=billboard&utm_campaign=endurance There is also an owners manual in the support section. 572xp.

Where is the 372xp-576xp and 390xp replacements? Surely someone must know... At least more than I....

I used my 562xp the other day to drop a nice black locust(I think...) After bucking it up, I couldn't get the purge bulb to pull fuel. It would pull mostly air, maybe 25% fuel. I got scared and didn't use the saw from then on. Wondering if anyone has seen this before. It pulled 100% fuel...

I have a 20" .325 pitch, .058 gauge Tsumura Light & Tough bar for sale. Husqvarna small mount K095. Comes with 2 full chisel chains. Husqvarna H21(Oregon 21lpx) Its an oddball with the drive link count though. 81dl. I made about 40 cuts with it and dulled the chains in some dirty wood. Gave up...

Looking to sell a Mastermind Ported 288xp that I received in trade a while back. I only made about a dozen cuts with it. It runs great. It has very good compression (I stopped pulling after 6 pulls and 190psi because my shoulder is messed up.) There is scoring. The intake and exhaust sides of...

Looking for a 350, 345, or 340 crankshaft in very good shape. Pictures please. Don't need bearings. Thanks, Dave.

Hey everyone, I need your opinions. I have the opportunity to buy a MS360 in good cosmetic shape, but has a scored piston and cylinder. Person I've been talking to wants me to make an offer. I don't even know where to begin. I was gonna offer $125. Is that high or low? What do you guys think?

I have an early Jonsered CS2260 in excellent condition for sale. No hesitation/idle issues. Can make a video upon request. Dual factory spikes, 2x fleece Air filter, 1x black mesh air filter, Extra WH model clutch cover(Not wider). Winter kit included (never installed). 16" 58 gauge, 20" 50...

I just realized today as I was putting my 20" bar on my 2260 that the oil slot on the saw is open to the side cover. The slots on the bar for the adjuster stud are machined too far out from the center. Oil would just flow right past and out of the bar nut retainers. Any ideas to solve this? The...

Here she is in all of her glory! New Jonsered CS2260 :cheers: And with a nice 3/8 20" bar Now to find some wood!!

While browsing youtube I came upon this video. Its the same old video everyone has already seen. But it was uploaded on December 17th, 2012, from Jonsered USA. Anyone know anything about its release? This would make a perfect one saw plan. I want one!!!! http://www.youtube.com/watch?v=gNFEzdbvokw

Looking for experience. Will tachometers always register crazy numbers when a saw, or any 2-stroke for that matter, with a rpm limited coil is overrun? Or can/will they show what the saw has been bounced down to? Just curious...

2 complete 375k saws, 2 375k parts carcasses, and one 346xp fuel tank/trigger/handle. One complete saw has 95psi. Hoping I can save the cylinder. Also came with 2 extra jugs(not pictured), one with minimal aluminum transfer, one with a bunch. I am hoping to make a nice saw out of one. Anyone...

I have been recently having a problem with my saw. I was cutting some poplar when the saw started screaming in the cut. I stopped cutting and checked the rpm and it went way past the 14k I had it set at. I took the carb apart, cleaned it and reassembled. so how many turns out should i start with...

Hi guys, just curious what tools would be needed to remove the muffler, top cover, spark plug and chain/clutch cover. I found a used saw not too far from me and want to make sure I go prepared. I just want to check the basics. I figure spark plug, piston on the muffler side and inside the spark...

I figured you guys would get a kick out of these.. This one is a homeowner (Same Homelite I first owned), who should not have a saw, a lot of wrongs... Love the grin as it falls towards him. http://www.youtube.com/watch?v=40XSyybjtj4&feature=related and then this one, ouch...

Any ideas? Just curious. http://westernmass.craigslist.org/grd/2031495734.html Lancastere?