Swap meet...

[HighGuy]

Old Jonsered parts

Looking for a place to get some older J'Red parts:

910 crank seals (difficult?)
a 24"-28" bar (Jonsered or Homelite large studs (10mm?)
bar guide plate(s)

625-630-670 clutch covers (I know with a brake is tough)
bar guide plates
handle(s)

601 & 621 crank seals (set of each, but I think they are the same, anyway)

Any of the above, will help.

Thanks in advance.

 

[Jacob J.]

Looking for a place to get some older J'Red parts:

910 crank seals (difficult?)

The crank seals are generic, there's a number of Husqvarna crank seals that will fit. I believe the seals from the 181/281/288 are the same, but would need to measure to make sure.

 

[HighGuy]

The crank seals are generic, there's a number of Husqvarna crank seals that will fit. I believe the seals from the 181/281/288 are the same, but would need to measure to make sure.

No kidding. I appreciate any research into it. I will take a look into it more tomorrow. Make some calls.
That would be good thing to hear.

Thanks much, Jacob.

Working on my saws today, I ask one of the younger guys, "Find me a Diversified "Retro" Chainsaw Parts Dealer?" (Attempt to keep up with the times???)

-Guy-

 

[epicklein22]

Still on the hunt for a handle bar for a 024/026. Lots to trade or green.

I also have the following saws up for grabs and they are woods ready: 066, 372xp, 394xp.

 

[treetrasher]

372

how much for the 372

 

[caddguy]

Need full wrap for a 394XP

Looking for a wrap for the 394 series saw.
Thanks!

 

[7hpjim]

How much for the 394,some pics and a health report :hmm3grin2orange:

 

[7hpjim]

r440

Need parts for a Partner R440, piston c-clips rings possibly pin and bearing, air filter, crank seals

 

[ric5141]

Mac PM 850

Looking for a parts saw

 

[warjohn]

Still on the hunt for a handle bar for a 024/026. Lots to trade or green.

I also have the following saws up for grabs and they are woods ready: 066, 372xp, 394xp.

I think I have one, I will try and look tonight.

 

[Mastermind]

Trying to find a rear handle for a Pioneer P 42.

 

[sefh3]

Trying to find a rear handle for a Pioneer P 42.

I think I have one for a P40? Will that work?

 

[Mastermind]

I think I have one for a P40? Will that work?

Pioneers are still new to me. I bet I can find out though.

 

[sefh3]

PM me if they are the same. I'll check mine out tonight.

 

[epicklein22]

how much for the 372

How much for the 394,some pics and a health report :hmm3grin2orange:

I have the saws in the trading posts. I will post a link to them when I get some more time later this evening.

 

[fredmc]

Still on the hunt for a handle bar for a 024/026. Lots to trade or green.

I also have the following saws up for grabs and they are woods ready: 066, 372xp, 394xp.

I'll getcha a handle, I need the plastic airbox/cylinder divider for a 262?

 

[mdavlee]

How much for the 394,some pics and a health report :hmm3grin2orange:

Here's the link for it. http://www.arboristsite.com/pp-classifieds/showproduct.php?product=4602&cat=6

 

[Teddy.Scout]

Looking for a 066 carb., piston and a rim drum.

Thanks Guys!!!

 

[sefh3]

Pioneers are still new to me. I bet I can find out though.

Yes I have one but no you can't have it.... it's busted. Sorry

 

[warjohn]

Still on the hunt for a handle bar for a 024/026. Lots to trade or green.

I also have the following saws up for grabs and they are woods ready: 066, 372xp, 394xp.

I do have a handle bar. It might take me a few days to get it iff and get it ready to ship.