Swap meet...

[Arrowhead]

I've got hundreds of .325 tie straps... just the strap, no presets. I think they are Windsor branded. I've used them on either Stihl or Oregon chain before. I believe one of the brands required drilling them out just a hair.
If anybody could use some... let me know.

Anybody else needing any? They're free.

 

[DSS]

Honestly I have used my ebay knock off about 100-150 times now and it works great!
Bench Model Rivet Spinner Repair Shop Chain Maker Tool | eBay

You really don't need a breaker if you have a bench grinder and a nail punch. hell 90% of the time I just grind the exhisting tie strap down really far on the bench grinder and then twist the chain and it pops apart. Saves cost on break and breaker tips (the tips will break if you don't grind rivets a little).


let me check for spark and cylinder condition. not sure if this saw is up for trade or a fixer upper yet...
It needs the 1/2 wrap and support brackets and clutch cover...

Lemme know what you need. I think I still got your address.

 

[RedneckChainsawRepair]

Anybody else needing any? They're free.

If you think they will work on 33LG oregon chain, could I get some.

Got partial roll left and out of of new straps. Just been using used off old chains.

 

[Arrowhead]

If you think they will work on 33LG oregon chain, could I get some.

Got partial roll left and out of of new straps. Just been using used off old chains.

Kevin

I've been using them on 34LG chain. They need a slight modification. If I remember correctly... the holes need to be widened just a hair. I use a 1/16" carbide Dremel burr. It only takes seconds. Ive never had any problems running it.
PM me your address.

 

[RedneckChainsawRepair]

Kevin

I've been using them on 34LG chain. They need a slight modification. If I remember correctly... the holes need to be widened just a hair. I use a 1/16" carbide Dremel burr. It only takes seconds. Ive never had any problems running it.
PM me your address.

Sent,

Thanks.....

 

[Arrowhead]

I've had this saw for awhile. It needs a P/C. It's actually built half way decent. I think it would make a dam fine saw with 16"s of PS3.
It looks like new under the grime. I got stuff to trade if anybody has a P/C for it.

 

[tbone75]

I've had this saw for awhile. It needs a P/C. It's actually built half way decent. I think it would make a dam fine saw with 16"s of PS3.
It looks like new under the grime. I got stuff to trade if anybody has a P/C for it.

I think I can fix ya up Ed ! I will look tomorrow !

 

[Big_Wood]

my grandfather has cracked the fuel tank on his leaf blower. not a chainsaw but figured I would get some hits here. i'm hoping someone can help him out. he has been told time and time again by dealers in Canada and the states that the tanks are nla. he has tried many attempts at a fix without success. i'm hoping to get him going again. sorry for the sideways pic. please PM if you can help

 

[HittinSteel]

In need of a clutch for a Husky 2100

 

[cutforfun]

Looking for a good piston and rings for a ms200 or 200t. lots to trade or cash

 

[Jordan3605]

Cleaning up the garage......
Mini Mac Parts
PM 610
D-44 project saw
Homelite Super EZ -runs
Homelite Super 2 -runs
Homelite XL-12 -runs
Homelite DM-54 cut off saw -runs but will need carb cleaned

All available to good homes.......

looking for :
2100 cd chain adjuster.
026 pro clutch,needle bearing, clip, sprocket,

 

[cbfarmall]

Anybody have a rocker style kill switch for an older Jonsered 630? Somebody rigged mine with a toggle and I'd like to make it right. Also looking for inner and outer bar plates for the same saw.

Thanks, Chris B.

 

[Big_Wood]

got to digging through my parts today and realized I have enough to build me another 372 and 365. I do need a few things though.

I need:
recoil
ignition module
a usable 365 piston would be cool. it can be a piston from an early open port or later closed port as I have spare cylinders for both.

I would like to do this as a trade where both sides pay their own shipping as my paypal has been acting up. I've been trying to straighten it out over the last few days with no luck but will keep trying. if I can get it going I can pay for stuff again ebay here I come

 

[procarbine2k1]

I am in need of a Homelite 1050, 1020, 1130G piston and cylinder for my XP1020. I may be able to get by with just a piston and rings. Any used stuff will be just fine. Real sweet saw that was gifted to me by a fellow member, it would be special to me to get it going and would make a fine GTG saw. Saw is apart, cleaned, and almost ready to roll...
Will trade, cash or vinyl decal services or both.

 

[cbfarmall]

Anybody have a rocker style kill switch for an older Jonsered 630? Somebody rigged mine with a toggle and I'd like to make it right. Also looking for inner and outer bar plates for the same saw.

Thanks, Chris B.

Looking more closely, it looks to be a sliding type switch, not rocker. I wonder if the current style is the same?

Chris B.

 

[Big_Wood]

looking for a clutch for a 3120. one of mine decided it would be fun to grenade it's clutch mid cut . I can't afford to be going out without a spare mill saw as it is quite a distance away. unfortunately my 2nd spare 3120 already donated it's clutch to my spare 3120 a couple months ago. 2 clutches would be cool but 1 is really all I need. clutch shoes would work also as I have a spare carrier. everyones gotta have a few 3120 clutch shoes laying around I have some stuff to trade

bump I do understand that the hacker has reduced the traffic on this site but just hoping someone with what I need eventually see's this

 

[fastLeo151]

I am in need of a Homelite 1050, 1020, 1130G piston and cylinder for my XP1020. I may be able to get by with just a piston and rings. Any used stuff will be just fine. Real sweet saw that was gifted to me by a fellow member, it would be special to me to get it going and would make a fine GTG saw. Saw is apart, cleaned, and almost ready to roll...
Will trade, cash or vinyl decal services or both.

I may still have some 1130 nos rings.... ill check

 

[RedneckChainsawRepair]

Anybody have a rocker style kill switch for an older Jonsered 630? Somebody rigged mine with a toggle and I'd like to make it right. Also looking for inner and outer bar plates for the same saw.

Thanks, Chris B.

Chris try the inner bar plate from poulan 415-505 jonsered 2077 2083 :msp_wink:. I dont know if the outer are different or not. Check part numbers.

 

[mitch95100]

I need a good ms660 carb.

Sent from me to you using my fingers

 

[cat-face timber]

Husky 288 Case/Flywheel up for trade

Husky 288 Case/Flywheel, gas tank and 2 mufflers.


I do not want $$$, I would rather trade for project saws.

Must be Husky/Jonsered though..

thanks!