I may be interested in the bar if its never been bent and in good shape.
PM will be sent.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I may be interested in the bar if its never been bent and in good shape.
PM will be sent.
Wagnerwerks
The underdog..
I'm looking for a rim drum and a 1/4" rim for a stihl 017-025.
nevermind , ordered off ebay
Big_Wood
westcoast dweller
how many do you need? LOL
Just one.
Big_Wood
westcoast dweller
Just one.
hit me up with a PM tomorrow morning as a reminder for me. i know i have mufflers but not sure on the studs but i'll take a look. i should have some somewhere.
Jon1212
Riff Raff Fart Knocker from other Forum's.
In need of a few parts for a Jonsered 2095.
Clutch cover, brake assembly(including handle), outer spike, cylinder cover, and a muffler that isn't caved in.
I have PayPal, and NOS guide bars to trade.
TIA,
Jonathan
Clutch cover, brake assembly(including handle), outer spike, cylinder cover, and a muffler that isn't caved in.
I have PayPal, and NOS guide bars to trade.
TIA,
Jonathan
Looking for a high top AF cover for a 385/390 and a brake flag and flat spring for a 272. Have a low top 385 cover and other parts and funds to trade.
Some of you may have noticed I keep having coil issues. First the XL 102. Then the XL 12. Then the XL 123. Then the C 5.
Now my EZA. got three points type coils; one never works and two are sporadic. I tested continuity with an ohmmeter. Both with and without the HV lead
Need points type coil for a homelite EZA.
Now my EZA. got three points type coils; one never works and two are sporadic. I tested continuity with an ohmmeter. Both with and without the HV lead
Need points type coil for a homelite EZA.
Wagnerwerks
The underdog..
I need some 1/4" rims. I have 404 rims to trade or lots of other parts or cash. Thanks.
Jon1212
Riff Raff Fart Knocker from other Forum's.
C'mon, someone's gotta help a brotha out.
Big_Wood
westcoast dweller
looking for a bunch of 346 parts guys.
muffler
muffler bracket
muffler gasket
muffler bolts x2
muffler heat shields x2
metal intake clamp x2 346 and a 357
filter holder/choke/kill lever/air filter
throttle/op presence spring x3
op presence lever x2 346 and a 357
trigger linkage x2 346 and a 357
2 course thread OE ignition module screws
4 course thread OE air box base plate screws
good piston
K095 bar .325 18"-20"
i just got back from the dealer and all they had out of this list was a set of muffler bolts so i only need one set. i realize some of this stuff will have to be dealer ordered but just seeing if someone has some stuff around they don't mind sending down the line. got 2 346's and a 357 i'm bringing back from the dead on limited income. any help is greatly appreciated. got stuff to trade.
muffler
muffler bracket
muffler gasket
muffler bolts x2
muffler heat shields x2
metal intake clamp x2 346 and a 357
filter holder/choke/kill lever/air filter
throttle/op presence spring x3
op presence lever x2 346 and a 357
trigger linkage x2 346 and a 357
2 course thread OE ignition module screws
4 course thread OE air box base plate screws
good piston
K095 bar .325 18"-20"
i just got back from the dealer and all they had out of this list was a set of muffler bolts so i only need one set. i realize some of this stuff will have to be dealer ordered but just seeing if someone has some stuff around they don't mind sending down the line. got 2 346's and a 357 i'm bringing back from the dead on limited income. any help is greatly appreciated. got stuff to trade.
Jon1212
Riff Raff Fart Knocker from other Forum's.
Shane,
I have guide bars, but I fear it would be cost prohibitive shipping them to Canadia, with the Canuckastani exchange rate, and stuff.
I have guide bars, but I fear it would be cost prohibitive shipping them to Canadia, with the Canuckastani exchange rate, and stuff.
Big_Wood
westcoast dweller
the exchange rate ain't that big of a deal. it's COD charges that are crazy but as long as the value of the item is under $200 it's very little. just had those boxes of 346's and a 357 show up to find it was a $55 COD charge i was looking at the dealer here and an 18" .325 .058 homeowner bar was $60. $10 more will get me tsumura RW and $20 more will get me a cannon. i might just do that even cause i just order them from not far away at all so the shipping is free. interested in what you have though jon. i'll have to go back to your bar thread in the trader.
i was looking at the dealer here and an 18" .325 .058 homeowner bar was $60. $10 more will get me tsumura RW and $20 more will get me a cannon. i might just do that even cause i just order them from not far away at all so the shipping is free. interested in what you have though jon. i'll have to go back to your bar thread in the trader.
Jon1212
Riff Raff Fart Knocker from other Forum's.
I was joking about the exchange rate.
nmurph
ArboristSite.com Sponsor
Why haven't you PM'd me???? I feel overlooked.
Jon1212
Riff Raff Fart Knocker from other Forum's.
So says the resident midget.
