No the 650 never came with an RA muffler on it, the 650 was the last of the 600 series saws and used the same muffler as the 620, 620 Super
Pioneer chainsaws
- Thread starter WesternSaw
- Start date
-
- Tags
- operator manual
Help Support Arborist Forum:
No the 650 never came with an RA muffler on it, the 650 was the last of the 600 series saws and used the same muffler as the 620, 620 Super
I have seen Joe's 1200B on youtube. I am almost sure I can find room on a shelf for the P61
I picked these two saws up today at a yardsale. First saws I have found in weeks. The 61 is in good running condition and has the full covered muffler without the chainbreak. There is no hole in the top for the chainbreak. I am sure I will find a good home for the Reed Prentice.
Yard sales?!!!
Dang, you canuks have all the fun.:msp_w00t:
thanks for that, guess I got a decent spare. like the way it sounds, thinkin it would be nice on 1690, don't like tin can that's on it. seems like baffle is maybe missin... you got 650 parts I need? looked @ chainsawr, no luck there. any ideas where else to look? thx. pete.
Last edited:
huck01955
ArboristSite Guru
[video=youtube;156Ej7UWeBk]http://www.youtube.com/watch?v=156Ej7UWeBk&feature=share&list=UUhJFcViE8FQ5EIorHiLkUjQ[/video]
Hear is my 1200 B
Reed Prentice 1200 B - YouTube
Hear is my 1200 B
Reed Prentice 1200 B - YouTube
Mine was a lot quieter Joe and no smoke. Come to think of it, it doesn't make any noise at all.
Maybe someday it will run as nice as yours.
huck01955
ArboristSite Guru
P42 carb help
My P42 has been running great but I started it last night just to hear it run and it would die when I squeezed the trigger. Now it won't restart. I checked spark and it's good so I'm feeling like it's a fuel problem. What should the needles be set at to start trouble shooting?
My P42 has been running great but I started it last night just to hear it run and it would die when I squeezed the trigger. Now it won't restart. I checked spark and it's good so I'm feeling like it's a fuel problem. What should the needles be set at to start trouble shooting?
If it has the Tillotson carb on it the L should be around 1 -1 1/8 turns out and the L around 7/8 - 1 turn out to start off with, then adjusted for both idle and WOT after the saw is running.
Thanks, that's what I needed to know. I figure the second adjustment is the "H".
Last edited:
Check the fuel line inside the tank. It's common for them to crack at the nipple where the line exists the tank.
If you need any parts, let me know.
IEL Pioneer Twin
An IEL Pioneer twin parts saw. I have been looking for a complete clutch for quite a while. This saw came from the big auction in BC. I was lucky enough to have a very nice couple from BC send this saw to me. The saw was in one of about 18 bins full of parts and pieces. The serial number is very low
PT0493-3
An IEL Pioneer twin parts saw. I have been looking for a complete clutch for quite a while. This saw came from the big auction in BC. I was lucky enough to have a very nice couple from BC send this saw to me. The saw was in one of about 18 bins full of parts and pieces. The serial number is very low
PT0493-3
An IEL Pioneer twin parts saw. I have been looking for a complete clutch for quite a while. This saw came from the big auction in BC. I was lucky enough to have a very nice couple from BC send this saw to me. The saw was in one of about 18 bins full of parts and pieces. The serial number is very low
PT0493-3
people in Chilliwack I met few wk ago had one, & other stuff. am I close? just curious....
Got the saw fixed last night and saw your post this morning. You were right though. Turned the saw on it's side and gas was going everywhere. Tracked down a break in the fuel line and did a temporary fix. What size Tygon do I need? I'm assuming that would be the best replacement.
That would be the right area. I am just glad they agreed to send me the saw. I could not get to the auction, and the auction company would not ship. All items were to be removed in 24 hrs. I watched the saws and parts sell online but I have been told the online results and what stuff sold for don't add up. A lot of stuff was grouped together and sold for one bid??? Wish I could have been there.
Last edited:
often wondered about online & phone bidding...
huck01955
ArboristSite Guru
An IEL Pioneer twin parts saw. I have been looking for a complete clutch for quite a while. This saw came from the big auction in BC. I was lucky enough to have a very nice couple from BC send this saw to me. The saw was in one of about 18 bins full of parts and pieces. The serial number is very low
PT0493-3
Very nice Jeff glade to see you got it
opcorn:It uses 1/8" id 1/4" od. The piece inside the tank is 5 1/4" long and a 7 1/4" piece to the carb.
huck01955
ArboristSite Guru
Pioneer 600
Got a Pioneer 600 and a couple of other saws today
Got a Pioneer 600 and a couple of other saws today
Got a Pioneer 600 and a couple of other saws today
Nice haul J. You have to love those old mufflers on the Pioneers.
Tim
