Swap meet...

[sld961]

Replacement handle bar for Stihl models 034, 036, MS340, MS360. Replaces OEM: 1125 790 1751

Thanks. I found a used OEM one on eBay for 27 shipped.

Sent from my SCH-I535 using Tapatalk 4

 

[sld961]

Looking for a starter pawl kit for an 034. Figured I'd see if anyone had one laying around before I eBay it.

Thanks

Sent from my SCH-I535 using Tapatalk 4

 

[DSS]

I need a one piece coil for a 61 husky. I know next to nothing about them, is this a common coil?

I have assorted junk and cash.

 

[firefighterwolf]

very common

I need a one piece coil for a 61 husky. I know next to nothing about them, is this a common coil?

I have assorted junk and cash.

Yes. The Husky 61 used the same coil as the Husky 162, 66, 266, 268, 272. I believe its the same as the 50, 51, 55, 154, 254, 257, 261 & 262 also.

Ebay aftermarket new from china $10 or from USA (chinese made) $17.

Ignition Coil for Husqvarna 50 51 55 254 257 261 262 XP 61 268 268XP 272 272XP | eBay

Ignition Coil Fits Husqvarna 268 50 51 55 254 257 261 262XP 61 268XP 272 272XP | eBay

 

[Wagnerwerks]

I need a one piece coil for a 61 husky. I know next to nothing about them, is this a common coil?

I have assorted junk and cash.

If firefighter is right, I think I have one on a 50 that you can have for shipping.

Let me know.

 

[nmurph]

Does anyone have a starter assembly for a 6401???? Government vouchers available for trade (maybe some 346/353 parts also).

Bump...still looking.

 

[jockeydeuce]

I need a one piece coil for a 61 husky. I know next to nothing about them, is this a common coil?

I have assorted junk and cash.

I can send ya one tomorrow, Chris...PM me your addy.

 

[Arrowhead]

I need a jug for a Stihl MS310 or a good 45mm MS290 piston.
Most 290's are 46mm, I ended up with a 45mm jug.
Or any good 290/310 piston/cylinder combo.
I also need a muffler for the same type saw.
Got plenty to trade.

 

[c_silva88]

I need a jug for a Stihl MS310 or a good 45mm MS290 piston.
Most 290's are 46mm, I ended up with a 45mm jug.
Or any good 290/310 piston/cylinder combo.
I also need a muffler for the same type saw.
Got plenty to trade.

I got a ms290 muffler if you want ill throw it in the box with the saw before i ship it out

 

[machinisttx]

I need a jug for a Stihl MS310 or a good 45mm MS290 piston.
Most 290's are 46mm, I ended up with a 45mm jug.
Or any good 290/310 piston/cylinder combo.
I also need a muffler for the same type saw.
Got plenty to trade.

I've got a 310 jug out in the shop. The piston was scored on that saw and I didn't even look to see if the jug would clean up. I'll look this weekend. Also have a 290 jug that I partially cleaned up. No pistons though.

 

[procarbine2k1]

Looking for a nice, early 066 tank. The early non-transparent tank preferred, but either one will do. The cleaner the better. Trying to find one for a friend, hes helped me out plenty and I would like to find one for him. NOS would be great too, just PM me a price or what you need in trade.

 

[leecopland]

poulan p3314ws

Hi Folks,

Need the chain brake mechanism and the clutch cover to get this little guy off my bench. Other than the missing parts runs great.

Thanks,

Lee:msp_sneaky:

 

[wigglesworth]

I find myself in need of a poulan 3500 piston and a tilly 395 carb

I've got lots of parts to trade or $$??

 

[rocketnorton]

lookin for poulan oem bar "sprocket nose"

have 4200 w/26" Windsor, want 20-24" oem "sprocket nose", will consider other lengths...View attachment 313339 have parts or $.

 

[rocketnorton]

Hi Folks,

Need the chain brake mechanism and the clutch cover to get this little guy off my bench. Other than the missing parts runs great.

Thanks,

Lee:msp_sneaky:

have one for 42/18, craftsman grey, yours if u can use it...

 

[nstueve]

Bump...still looking.

neal,
your muffler and cover went out yesterday on 2 day priority. Maybe it will make it there by sat.???
cheers!

I need a jug for a Stihl MS310 or a good 45mm MS290 piston.
Most 290's are 46mm, I ended up with a 45mm jug.
Or any good 290/310 piston/cylinder combo.
I also need a muffler for the same type saw.
Got plenty to trade.

Ed,
I might have a P&C, let me look tonight. I know for sure I have a ms290 cylinder that will clean up if someone has the 46mm piston for it??? The piston I have, had a screwdriver stuck in the exhaust to lock the piston. The piston has a nice gouge on top and the top ring was stuck...

Also if someone happens to have a ms310 47mm jug I have a good piston for it!

 

[Warped5]

have 4200 w/26" Windsor, want 20-24" oem "sprocket nose", will consider other lengths...View attachment 313339 have parts or $.

Those do show up regularly on eBay ... just looked and there are several, just none in the lengths you're looking for

 

[rocketnorton]

Those do show up regularly on eBay ... just looked and there are several, just none in the lengths you're looking for

thanks, just would rather deal w/people here. no rush...

 

[Eccentric]

have 4200 w/26" Windsor, want 20-24" oem "sprocket nose", will consider other lengths...View attachment 313339 have parts or $.

I have an almost new 20" Poulan Pro branded Oregon replaceable sprocket nose bar (Oregon PowerMatch) that I'd trade for that 26" Windsor. D007 mount which works on Homelite XL-series, these midsize Poulans, and some Pioneer/Pioneer-Partner/Poulan Pro saws. Bought it NOS on ebay and only did a dozen or so cuts with it (in cottonwood and Douglas Fir logs at the PNW GTG). 3/8"-.058G. Takes a 70DL loop. Here it is on my Poulan 4000. It's a great bar for these Poulans. I just don't run 3/8-.058G chain.

In the pics he adjuster is at the end of it's travel because I had a 72DL loop on it (2 DL too long). Worked fine, but had no adjustment left. That loop went away with another bar in trade.

Would trade it for some folded green presidential pictures or possibly other parts (including a trade towards a good 32"-34" 3/8 pitch large Husqvarna mount sprocket nose bar) as well. No the 4000 is not for sale/trade.

 

[psuiewalsh]

Everything is for sale for the right price.opcorn: