The Sleeper 024S Build

[Termite]

024 is my favorite Stihl even though I've never owned one.

 

[Adirondackstihl]

024 is my favorite Stihl even though I've never owned one.

Sell ya one

 

[SawTroll]

The 024 has a 1 mm shorter stroke, and a smaller bore (42 mm) than a 026. An 024 Super has the same stroke as a 026.......but still has a 42 mm top end.

The 024 super case is the same as the early 026, but the 024 is different in that the crank throw area is smaller.

2 mm shorter, 30 vs. 32.

 

[Mastermind]

2 mm shorter, 30 vs. 32.

Correct.

I always think about the difference in the squish area.

I can cut .0393" (1mm) out of the squish, and may a 024 jug work on an 026.

 

[glock37]

Can u put a 026 top end on a 024 bottom end with the small case volume


Sent from my iPhone using Tapatalk

 

[Mastermind]

If you cut 1mm off the base.

 

[glock37]

Would it be a benefit with the small case volume or is it so small it wouldnt matter


Sent from my iPhone using Tapatalk

 

[Mastermind]

I'm normally wanting to got the other way.

I wonder how the 024 top end would run on the 026?

 

[Paragon Builder]

I'm normally wanting to got the other way.

I wonder how the 024 top end would run on the 026?

So then what's the benefit of the 026 jug on the 024? Why not just port the 024 jug?

 

[Mastermind]

Just a displacement increase. I'm not sure the 024 top end couldn't be made to run just as well.

 

[Deets066]

Sell ya one

Super?

 

[STIHLTHEDEERE]

Sell ya one

ok, ................pics?

 

[Deets066]

ok, ................pics?

You get the h$ll outa here I called it first

 

[Adirondackstihl]

I'll have to upload some to Photobucket

 

[Adirondackstihl]

Super?

No
024 AV WoodBoss

 

[CapitaineHaddoc]

Nice thread Randy. There's a mesh filter for sale from Sagenspezi, her,

http://shop.saegenspezi.de/Filtre-r-air-pour-Stihl-024-MS240-MS-240

Will this fit a 024?

 

[Adirondackstihl]

Mesh filter shipped this AM

 

[Mastermind]

Nice thread Randy. There's a mesh filter for sale from Sagenspezi, her,

http://shop.saegenspezi.de/Filtre-r-air-pour-Stihl-024-MS240-MS-240

Will this fit a 024?

Sir no sir.

That one will fit the later 026 though.

 

[KMSwr]

Thanks Roger. I buy lots of stuff from McMaster........never knew they had that mesh though.

Rumor has it you have an 024s standard p/c that you might not need and could sell?
I have an 024s that I over spent on to buy and now need at least a piston,I should have looked closer at the gray spark plug the 1st time I took it out,and the low 110psi compression,.Lesson learned?
I 've never done a piston swap on one of these,the only hassle is the intake boot?
Thanks alot

 

[Adirondackstihl]

Rumor has it you have an 024s standard p/c that you might not need and could sell?
I have an 024s that I over spent on to buy and now need at least a piston,I should have looked closer at the gray spark plug the 1st time I took it out,and the low 110psi compression,.Lesson learned?
I 've never done a piston swap on one of these,the only hassle is the intake boot?
Thanks alot

Check with Fatarrow.
He has a minty 024S cylinder he may part with.