What's on your bench? 5-7-2011

[blsnelling]

I just finished porting this MS880. I'm still waiting on some clutch parts to finish it up.

<object width="640" height="390"><param name="movie" value="http://www.youtube.com/v/xYpE7ICL-uI?fs=1&amp;hl=en_US&amp;rel=0"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/xYpE7ICL-uI?fs=1&amp;hl=en_US&amp;rel=0" type="application/x-shockwave-flash" width="640" height="390" allowscriptaccess="always" allowfullscreen="true"></embed></object>

 

[STLfirewood]

I hope I know what's going to be on your bench next week.

Scott

 

[blsnelling]

I hope I know what's going to be on your bench next week.

Scott

I should have it by Monday or Tuesday I'd think.

 

[Racerboy832]

Those flippy caps on the MS880 make me angry. Do they have them on the 660 yet?

 

[blsnelling]

Those flippy caps on the MS880 make me angry. Do they have them on the 660 yet?

No.

 

[ttyR2]

Just finished a good cleaning, tuneup, new fuel line/filter, clutch drum and drive hub.

Runs like a...well not quite million bucks, but runs very nicely.

 

[tbone75]

Nothing !! I quit for the day :hmm3grin2orange:

 

[leeha]

Full resto's on 2 more geardrive Mac's.
And not with there original motors.




Lee

 

[homelitejim]

[video=youtube;e8GkdsXZdkA]http://www.youtube.com/watch?v=e8GkdsXZdkA[/video]

Fixed a few small issues with this saw and now it is in the running category. Husqvarna 2100CD I think a 1983 model but not 100%. The bar is a 30 inch sugi hara with 100 dl's of Oregon skip tooth, I think a 50" bar is in order as I found a new used bar source. Not to shabby for $150.

 

[stihl 440]

lets see...a stihl 460 that im building, and a husky 372xpBB and a 385xp.

 

[fidiro]

Does it have to be just saws or anything?

I'll just go ahead and say it, I've got two blowers completely tore down and waiting for parts from RedMax. One EB7001 and EBZ8000. I don't think I'm going to do the work you do to your saws on these two but they did clean up very nice.

 

[Mr. Bow Saw]

Full resto's on 2 more geardrive Mac's.
And not with there original motors.




Lee

I wonder what this will be.

 

[caleath]

ms 210 getting new crankshaft seals and some port work. 038 magnum waiting on parts for the starter. I thought the 066 woud be apart but the puller for the flywheel was wrong.

I did a whole bunch of parts cleaning today too. I have the start of a 044/460 cleaned up.

Who knows whats next.

 

[o8f150]

i haven't found anything locally for weeks now :bang::bang::bang::bang:

 

[Roanoker494]

Grandpa's mini Mac that I inherited

Got it running today with a good cleaning, fuel line and carb cleaning.

 

[jockeydeuce]

A pristine 084 getting a good clean up and checked over before it hits the open market.

 

[Nailsbeats]

240lbs right now.

 

[masculator]

An 034 That has been in the family since new, going for a ground up rebuild after finding bearing probs. going to give it a mild port tickle, new rings, bearings, and a full gasket set. Also getting a new crankcase cause it had spun the clutch side bearing in the crankcase and elongated the seat.

and my new Ms660 is sitting on the bench just waiting for the opportunity to cut something.

 

[Work Saw Collector]

This week a 066 flat top.

A 36” Cannon Superbar almost ready for Powder Coat.

Cannon superbar by supercabs78, on Flickr

Case Halfs allmost ready.

Case halfs by supercabs78, on Flickr

Might take a month but I'm well underway on it.

 

[camo]

Stihl 029 super that I just got today. Got to take her clotes off for a good cleaning. need a cover adn a few other pieces but its running good after a good carb clean and a tune up. Followed by a poulan 33 cc. Got it today too. Just needed a good service and its up adn running.