Swap meet...

[gregz]

I have a 20" oregon cheapo bar and two brand new oregon safety chains
stihl mount fits 026 260 ????
.063 .325 all new never used

I also have a pair of Husqvarna chaps waist one size fit all and 36" L
there new never used just garage dirt on em

I have no use for any of it, if you have something to trade ???? whatever
cheers
gregz

 

[stihlkicken]

solid 064

064 w/3 foot bar,404 chain.will trade for equal condition husky 2100.

 

[2000ssm6]

I got a Husky 55 in pretty bad shape but mostly complete. For it to run this is the list I can come up with, if anything is missed ya'll remember I'm a Stihl man!

Recoil is stripped out; the white piece that spins the flywheel will need to be replaced. All recoil cover bolts are gone.

Top cover bolts gone. Air filter dirty as heck, so much for "air injection".

A piece of the crankcase looks to be broken on the front recoil side, it had a strip of sheet metal holding the top cover on that was screwed to the lower case for support. This is circled in YELLOW.

Front lower anti vibes busted/gone

No spark plug

Can't check compression because recoil is screwed up, p&c look good from the plug hole. I will remove p&c and confirm if needed. Crank bearings "feel" good, no roughness/binding felt when rotating with my hand.

Clutch cover nuts mis-matched but there.

Decomp knob broken off, doesn't move.

Oil cap has a tab broken off.

Chain brake works, LOL.

Bar is f-ed, will need a new b&c.

Trades: I'm interested in 200/200T, 026/260, 036/360, 044/440, 046/460 project saws or parts. I will post this in the classifieds if no action, for $100 shipped.

FredMC has first dibs, will update if this falls through.

 

[Saw Dr.]

I got a Husky 55 in pretty bad shape but mostly complete. For it to run this is the list I can come up with, if anything is missed ya'll remember I'm a Stihl man!

Recoil is stripped out; the white piece that spins the flywheel will need to be replaced. All recoil cover bolts are gone.

Top cover bolts gone. Air filter dirty as heck, so much for "air injection".

A piece of the crankcase looks to be broken on the front recoil side, it had a strip of sheet metal holding the top cover on that was screwed to the lower case for support. This is circled in YELLOW.

Front lower anti vibes busted/gone

No spark plug

Can't check compression because recoil is screwed up, p&c look good from the plug hole. I will remove p&c and confirm if needed. Crank bearings "feel" good, no roughness/binding felt when rotating with my hand.

Clutch cover nuts mis-matched but there.

Decomp knob broken off, doesn't move.

Oil cap has a tab broken off.

Chain brake works, LOL.

Bar is f-ed, will need a new b&c.

Trades: I'm interested in 200/200T, 026/260, 036/360, 044/440, 046/460 project saws or parts. I will post this in the classifieds if no action, for $100 shipped.

I have a nice mini MAC 120 (no spark) I'd trade even up.........

 

[2000ssm6]

I have a nice mini MAC 120 (no spark) I'd trade even up.........

 

[cjcocn]

I have a nice mini MAC 120 (no spark) I'd trade even up.........

LOL .... that made me laugh.

That cylinder show up yet?

 

[mowoodchopper]

I have two dolmar 111 s , I was going to rebuild one out of two, may not get it done. Both cyl are good, one is exc, one has good compression piston is exc
the only bad thing on this saw is the chain brake, i know of . The other saw has good case and brake but had low compression, by the looks of it , the saw needs seals and leaned out , piston shows scuffs not bad but ring was wore to and low comp. I was going to make 1 of two. Would trade for any saw stuff I could use. Or another saw.

These are 111 dolmars.

 

[fredmc]

parts

I just got a 66 husky, 50 husky, 2065 j-red. Can get a few 028's and a few 032's. any one wanna trade?

 

[nmurph]

WTB, 30-36" 3/8 bar for Mac 125....

 

[Bowtie]

Im looking for a set of new OEM 42mm rings for an 028 WB, or a P/C for an 28 Super (46mm). I believe the 42mm rings are the same for the 024/240, 030, and 028.

 

[fredmc]

Im looking for a set of new OEM 42mm rings for an 028 WB, or a P/C for an 28 Super (46mm). I believe the 42mm rings are the same for the 024/240, 030, and 028.

I can probably find you a 028 super part saw.

 

[HittinSteel]

I have A 16" .325 .063 Stihl ES bar in good condition. Looking for an 18" bar with the same specs.

 

[fredmc]

sawz

I got all these and they need good homes

View attachment 100513

View attachment 100510

View attachment 100509

View attachment 100512

View attachment 100511

 

[fredmc]

more sawz

more that need homes
View attachment 100515

View attachment 100517

View attachment 100516

View attachment 100514

 

[fredmc]

I got this echo also any one interested?View attachment 100519

 

[fredmc]

If no one wants these I'll put them in the tradin post for $75 a piece. PM me I'll let em go for less. whatcha got to trade?

 

[Meadow Beaver]

Anyone need some bars 42", 36", 32", 24"?
044 parts?
V-Stacks, foam filters?
394 parts?
Echo cs-3450 parts?
Other random part?

 

[valekbrothers]

Anyone need some bars 42", 36", 32", 24"?
044 parts?
V-Stacks, foam filters?
394 parts?
Echo cs-3450 parts?
Other random part?

What do the bars fit?

 

[MS460WOODCHUCK]

If no one wants these I'll put them in the tradin post for $75 a piece. PM me I'll let em go for less. whatcha got to trade?

Do any of them run?:monkey:

 

[Meadow Beaver]

What do the bars fit?

The 42" is a woodsmanpro husky mount lighty used with new tip, 36" reduced weight is a stihl mount and so is the 32" reduced weight and the 24" powermatch. All bars are 3/8"-.063"