Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I have a 20" oregon cheapo bar and two brand new oregon safety chains
stihl mount fits 026 260 ????
.063 .325 all new never used
stuffz102-1.jpg


I also have a pair of Husqvarna chaps waist one size fit all and 36" L
there new never used just garage dirt on em
stuffz072.jpg


I have no use for any of it, if you have something to trade ???? whatever
cheers
gregz
 
I got a Husky 55 in pretty bad shape but mostly complete. For it to run this is the list I can come up with, if anything is missed ya'll remember I'm a Stihl man!

Recoil is stripped out; the white piece that spins the flywheel will need to be replaced. All recoil cover bolts are gone.

Top cover bolts gone. Air filter dirty as heck, so much for "air injection".

A piece of the crankcase looks to be broken on the front recoil side, it had a strip of sheet metal holding the top cover on that was screwed to the lower case for support. This is circled in YELLOW.

Front lower anti vibes busted/gone

No spark plug

Can't check compression because recoil is screwed up, p&c look good from the plug hole. I will remove p&c and confirm if needed. Crank bearings "feel" good, no roughness/binding felt when rotating with my hand.

Clutch cover nuts mis-matched but there.

Decomp knob broken off, doesn't move.

Oil cap has a tab broken off.

Chain brake works, LOL.

Bar is f-ed, will need a new b&c.

attachment.php


attachment.php


attachment.php


Trades: I'm interested in 200/200T, 026/260, 036/360, 044/440, 046/460 project saws or parts. I will post this in the classifieds if no action, for $100 shipped.

FredMC has first dibs, will update if this falls through.
 
Last edited:
I got a Husky 55 in pretty bad shape but mostly complete. For it to run this is the list I can come up with, if anything is missed ya'll remember I'm a Stihl man!

Recoil is stripped out; the white piece that spins the flywheel will need to be replaced. All recoil cover bolts are gone.

Top cover bolts gone. Air filter dirty as heck, so much for "air injection".

A piece of the crankcase looks to be broken on the front recoil side, it had a strip of sheet metal holding the top cover on that was screwed to the lower case for support. This is circled in YELLOW.

Front lower anti vibes busted/gone

No spark plug

Can't check compression because recoil is screwed up, p&c look good from the plug hole. I will remove p&c and confirm if needed. Crank bearings "feel" good, no roughness/binding felt when rotating with my hand.

Clutch cover nuts mis-matched but there.

Decomp knob broken off, doesn't move.

Oil cap has a tab broken off.

Chain brake works, LOL.

Bar is f-ed, will need a new b&c.

attachment.php


attachment.php


attachment.php


Trades: I'm interested in 200/200T, 026/260, 036/360, 044/440, 046/460 project saws or parts. I will post this in the classifieds if no action, for $100 shipped.

I have a nice mini MAC 120 (no spark) I'd trade even up.........
 
I have two dolmar 111 s , I was going to rebuild one out of two, may not get it done. Both cyl are good, one is exc, one has good compression piston is exc
the only bad thing on this saw is the chain brake, i know of . The other saw has good case and brake but had low compression, by the looks of it , the saw needs seals and leaned out , piston shows scuffs not bad but ring was wore to and low comp. I was going to make 1 of two. Would trade for any saw stuff I could use. Or another saw.

These are 111 dolmars.
 
Last edited:
Im looking for a set of new OEM 42mm rings for an 028 WB, or a P/C for an 28 Super (46mm). I believe the 42mm rings are the same for the 024/240, 030, and 028.
 
If no one wants these I'll put them in the tradin post for $75 a piece. PM me I'll let em go for less.:) whatcha got to trade?
 
Back
Top