jerryw66
ArboristSite Guru
Bought this thing in 1986 or so, drove it home about 50 miles, took a while. It will still run but I don't have the time to get it going, maybe someday my boy will want it.
Wood Hauler Pics
- Thread starter bore_pig
- Start date
Help Support Arborist Forum:
Bought this thing in 1986 or so, drove it home about 50 miles, took a while. It will still run but I don't have the time to get it going, maybe someday my boy will want it.
That thing looks mean..
I like the front bumper!!
Coalsmoke
ArboristSite Operative
Somesawguy, great truck, whats all the yellow rolls / tubes on the back of the truck?
Thanks.................Creeker
treevet
Addicted to ArboristSite
Bought this thing in 1986 or so, drove it home about 50 miles, took a while. It will still run but I don't have the time to get it going, maybe someday my boy will want it.
That truck is very cool. Love to see some more picts if you got any. Does the winch work?
They are just tubes of grease that my dad picked up somewhere for free. All of that stuff will have to be moved to use it, but it has been sitting for a few years. You know how stuff collects around a stationary object.
Edmccabe
ArboristSite Member
Somesawguy;
It looks like the top end of your 216 - rocker shaft, rockers & valves - has not been receiving enough oil and may be plugged with sludge. On this engine the top oil is delivered past the bolts that secure the Rocker shaft - I don't remember exactly which ones - but in the late 50 when I was was a Chevrolet mechanic we often had to modify the bolts by grinding one side flat to allow a larger passage for the oil. We also used the bolts as a ram to free the oil passages below - we removed the bolts then filled their holes with oil - reinserted the bolt into the top of the hole and drove its down into the hole with a hammer - a pile driver of sorts.
These things have babbit bearings but will run forever with minimal care.
I had a 46 Chevy dump with a 1956 235 engine. I installed 24" single wheels with Bandag recaps on its 2 speed rear and found that it would go almost anywhere in the woods.
Good luck with keeping your truck running.
Ed
It looks like the top end of your 216 - rocker shaft, rockers & valves - has not been receiving enough oil and may be plugged with sludge. On this engine the top oil is delivered past the bolts that secure the Rocker shaft - I don't remember exactly which ones - but in the late 50 when I was was a Chevrolet mechanic we often had to modify the bolts by grinding one side flat to allow a larger passage for the oil. We also used the bolts as a ram to free the oil passages below - we removed the bolts then filled their holes with oil - reinserted the bolt into the top of the hole and drove its down into the hole with a hammer - a pile driver of sorts.
These things have babbit bearings but will run forever with minimal care.
I had a 46 Chevy dump with a 1956 235 engine. I installed 24" single wheels with Bandag recaps on its 2 speed rear and found that it would go almost anywhere in the woods.
Good luck with keeping your truck running.
Ed
Thanks for the tip Ed. It hasn't been run much for awhile, and that is likely why it looks a bit dry on the top end. We ran it for awhile on Saturday, and all the passages seemed to be seeping/pumping oil.
I'm glad it didn't sit for another season though, I think we would have had to take the head off to get things freed up. We had 3 stuck valves as it was. It took awhile to get them freed up.
It's running ok now, but we had a heck of a time getting it started the first time. It still skips a little bit here and there, but it's not too bad. Those old 6-volt systems are a little more finicky about clean connections, and good point contact.
I think we'll get some work out of the old girl yet this season.
opcorn:ChrHerrman
ArboristSite Lurker
Dump Trailer
I have a 2008 1/2 ton chevy truck with a 5.3 V8 and in my experience has just as much power as the larger 6.0 in 3/4 ton models. I bought a 5' x 8' single axle dump trailer with 5' high sides made by Pequea this spring and it is the best move I ever made. Load it up and dump it out. I no longer have trouble getting motivated to unload 1 1/2 cords of wood or a huge pile of brush. I have had 1 1/2 cords or green red oak and the truck pulled it fine and trailer dumped it just fine. Trailer is rated for 5000 lbs and I had at least 7000 lbs. on it without any trouble. I might be a little overweight sometimes but I can haul a lot with a small rig.
I have a 2008 1/2 ton chevy truck with a 5.3 V8 and in my experience has just as much power as the larger 6.0 in 3/4 ton models. I bought a 5' x 8' single axle dump trailer with 5' high sides made by Pequea this spring and it is the best move I ever made. Load it up and dump it out. I no longer have trouble getting motivated to unload 1 1/2 cords of wood or a huge pile of brush. I have had 1 1/2 cords or green red oak and the truck pulled it fine and trailer dumped it just fine. Trailer is rated for 5000 lbs and I had at least 7000 lbs. on it without any trouble. I might be a little overweight sometimes but I can haul a lot with a small rig.
200,000 miles
Ye ol' Dakota turned the 200,000 mile mark today on the way over to a friend's place to see if all the wind we got up here knocked any trees over.
Ye ol' Dakota turned the 200,000 mile mark today on the way over to a friend's place to see if all the wind we got up here knocked any trees over.
banshee67
Poulan Wild Thang
Ye ol' Dakota turned the 200,000 mile mark today on the way over to a friend's place to see if all the wind we got up here knocked any trees over.
congrats!
thats damn good, especially for a dodge:greenchainsaw:
Kingsley
ArboristSite Guru
:agree2:
Alan Smith
ArboristSite Operative
PT Cruiser
our PT Cruiser has 240000 still going dodge is Chrysler i have good service out of them
our PT Cruiser has 240000 still going dodge is Chrysler i have good service out of them
Alaskat
ArboristSite Member
Here are a couple of capable haulers road legal and go through the woods like no other truck. There is every conceivable attachment for these rigs as well. I run my splitter and the bed is a three way tipper. Made for the getting trees outa the woods and wood outa the trees. Gets me into some good moose country too. 20 spd trans w/ super crawler and snail,front and rear air lockers, front and rear 2 spd pto and 5.9 litre diesel. I like it better that the JD 450 w/ winch. Mine was a forestry truck in germany I bought it for 5K w/ 4000 hours and 140,000 Kms came with six new 395/85/20 tires that are 46" tall and the little 406 can go 6o mph all day long.
congrats!
thats damn good, especially for a dodge:greenchainsaw:
I bought it 4 yrs ago with only 140k on it, and as far as I know, still has the orginal engine and trassmission, too.
Gypo Logger
Timber Baron
Gotta haul that wood!
John
John
Junkfxr
ArboristSite Operative
I'd give body parts to have a good Unimog but they're way too far and few between and the few that I have found have been in the $25,000 range.
Alaskat
ArboristSite Member
I see a few on CL and the Unimog Exchange always has a good assortment.
A Chevy hauler............Creeker
First two ricks
Three ricks & more
Loaded
First two ricks
Three ricks & more
Loaded
