Swap meet...

[axlr8]

think I have some 51/55 parts, Ill get back to you in the AM. and If i dont, well...A reminder would be well.. I should have the choke and throttle rods.... But that clutch cover... they all get torn apart here!

 

[350jeepcj5]

got the case half covered...


still need a tank/handle assembly for a 038 super 2

 

[TonyRumore]

I need an air filter hanger/mount/tree for an 044.

 

[nmurph]

372

I need a 372 chainbrake handle and a half-wrap. Holler if you have one.

 

[Mastermind]

Hunting a 346 muffler brace.......please.

 

[Nardoo]

Wanting to swap a 51 clutch cover with working brake for a muffler to fit a Dolly 6000i (120S, 120Si etc). Would ideally suit a Vietnam vet....

Al.

 

[Scooterbum]

My IPL shows two different coils on the 020. 0000 400 1306 and 1114 404 3200.
The MS200 uses the same 0000 400 1306 coil.

Tony

Thanks Tony, I'll have to look and see which one it is.
Who would have ever thought Stihl would have 2 different parts for the same saw?

 

[Scooterbum]

Steve do you know of 200's are the same? I have a 200 coil

Checking today to see. Also will be going through the 075 stuff for you.
If you haven't made a deal on the Husky 44 I maybe interested. I'm also going to check that long bar I have hanging out there. I know it's .404, just not sure of mount. I'm thinking I had it on the 056mag II.

 

[Mastermind]

Wanting to swap a 51 clutch cover with working brake for a muffler to fit a Dolly 6000i (120S, 120Si etc). Would ideally suit a Vietnam vet....

Al.

Done. The cover I have is in very nice condition too......(just dug it out).

 

[sefh3]

Checking today to see. Also will be going through the 075 stuff for you.
If you haven't made a deal on the Husky 44 I maybe interested. I'm also going to check that long bar I have hanging out there. I know it's .404, just not sure of mount. I'm thinking I had it on the 056mag II.

Is this for an older 020AV (metal crankcase) or a new MS200 (plastic crankcase)?

 

[Scooterbum]

Is this for an older 020AV (metal crankcase) or a new MS200 (plastic crankcase)?

It's for an older 020AVS rear handle with electronic instead of points.

 

[RedneckChainsawRepair]

JonseredS 490 with heated handles

Got to many saws in the same size that are not going to get used.

Notice this one is JonseredS and not just Jonsered which makes it a little rarer from my research.

1982 Jonsered-S jonsered 490 with heated handles. Topend looks like brand new with crosshatch and witness lines etc.

Story: Basically a new saw still that was bought new by Marcel Vincent and then sold to another racer builder then to another and then I saved it before being butchered into a 3 cube race saw.

It just sets on my shelf and gets run at gtg's or comparison testing only since I have owned it. I bought it PHO = power head only. I found a 325 jonsered bar and put on it and a old jonsereds bar cover for it.

Just like to see someone get use or that collects saws to give this saw a home. It is just not going to get used here.

PM me with trade offers or wanting a more info.

 

[fastLeo151]

I need a 372 chainbrake handle and a half-wrap. Holler if you have one.

Do you need just the flag or the whole side cover? I have the whole thing.

 

[husqvarnaguy]

I know its not a saw but does anyone know where I can get some Ford 3910 tractor parts.

 

[tmessenger]

I need an air filter hanger/mount/tree for an 044.

I found one for my 044 build at Chainsawr.com a few weeks ago I think I paid $15 for it you might give them a call and see if they have any more.

TIm

 

[sefh3]

It's for an older 020AVS rear handle with electronic instead of points.

Here is what I have. Will this work? PM me your address if it will. It's from an 020AV.

 

[axlr8]

Heres my lot of 'stuff' to unload.

74 DL of .325 .063 oregon chain
Its got 22 on the driver, and 25 on the raker. used

Oregon EW 160xxxd009 16"? 3/8" sprocket nose VERY light use.

Oregon 180SLGK095 .050 .325x72DL hardnose, NEW

372 flywheel, slight rub marks, but usable

359 flywheel, Great used.

066 carb (parts)

And a lot of 5 or 6 zama and walbro carbs and pieces.

Looking to trade the carbs as one lot for a WT194

Otherwise.. Whatta ya got!? I have more small stuff to go through tomorrow!

Pm would be Ideal, but Ill check here aswell!

Thanks guys!!!

 

[axlr8]

Bumping to the new page and day. :msp_smile:

Hey Randy! I found you a throttle rod! No luck on the choke lever though! I do have a pawl-less flywheel, and your 650 Super cylinder waiting for some spare change to ship! You need any 372 plastic? I have that and a gutless clutch cover if your interested!

Im still working on getting a saw to send your way! Itll be a 70.7 ccs hopefully!

 

[Johnsobri]

Looking for a cylinder for a Husky 359 and piston. I've got some 026 parts to trade and paper.

I know trading Stihl for Husky isn't right but you gotta do what you gotta do. Trying here first before I go to northwood.

Bump

 

[jbird77]

helping

I am trying to help a friend out and get him a little bigger saw i would like to find a project . I would like to get somthing husky , in the 60 cc,s range , just droppin a line to see what comes up .