Stihl MS461 R

[Trx250r180]

ok who has a chainsaw dyno so we can see peak hp and tourque curves on a graph :hmm3grin2orange:

 

[Andyshine77]

I think you're talking about the difference between a saw that is intended for real work and a "worksaw" that is intended for a GTG toy.



If your saw will only turn 10,000rpm in the wood, why would it need to turn 16,000rpm out of it?

We've been over this countless times. Out of the wood rpm don't mean anything if the rpm's drop off sharply. However in most cases higher no load rpm's = higher in the cut rpm.

Sent from my Nokia 920 using Board Express

 

[thomas1]

ok who has a chainsaw dyno so we can see peak hp and tourque curves on a graph :hmm3grin2orange:

Timberwolf.

I think he got tired of the pissing contests and left.

 

[thomas1]

We've been over this countless times. Out of the wood rpm don't mean anything if the rpm's drop off sharply. However in most cases higher no load rpm's = higher in the cut rpm.

Sent from my Nokia 920 using Board Express

Isn't that what the Internet is for, beating dead horses?



Well, that and ####.

 

[srcarr52]

Mitch, I had to make a run to the store today after work to pick up some Creamy Dark because of you and your darn pictures.

 

[Jacob J.]

Mitch, I had to make a run to the store today after work to pick up some Creamy Dark because of you and your darn pictures.

Mitch is just a bad influence all the way around. He knows it full well too.

 

[HEAVY FUEL]

Mitch, I had to make a run to the store today after work to pick up some Creamy Dark because of you and your darn pictures.

Shawn, Sunday I went to the liquor store only to find the Creamy Dark was backordered! I immediately ran to Burnett Dairy & ordered up a half pound of fried cheese curds & started drowning my sorrow... I think I even felt the old ticker stutter a few times.

 

[Stihlman441]

We've been over this countless times. Out of the wood rpm don't mean anything if the rpm's drop off sharply. However in most cases higher no load rpm's = higher in the cut rpm.

Sent from my Nokia 920 using Board Express

Thats the point,TORQUE will keep the rpms up in the cut.:msp_smile:

 

[HEAVY FUEL]

Thats the point,TORQUE will keep the rpms up in the cut.:msp_smile:

 

[HEAVY FUEL]

Mitch is just a bad influence all the way around. He knows it full well too.

Easy now, Mitch is the only John Wayne left in this tooown!
:waaaht::waaaht:

 

[mweba]

Easy now, Mitch is the only John Wayne left in this tooown!
:waaaht::waaaht:

More like the shakiest gun in the west.










If we've met, you understand......

 

[mweba]

Some more pics. I know inside shots have been shared already.....


Untitled by mweba1, on Flickr


Untitled by mweba1, on Flickr


Untitled by mweba1, on Flickr


Untitled by mweba1, on Flickr


Untitled by mweba1, on Flickr

 

[srcarr52]

I like the intake port direction and shape.

 

[mweba]

And more...


Untitled by mweba1, on Flickr

This pic shows the clearance between piston and deflector/stuffer.


Untitled by mweba1, on Flickr


Cut with a well broke in 460 and the 461 today. Honestly the 460 felt faster while sounding like it held higher rpm's. After reviewing the vids, I was surprised to see the 461 turn in faster cut times in every different chunk of wood I threw at it. The gap at its greatest was 4 seconds and the best comparison video I got the gap was 1 second. That makes these saws very close but one must keep in mind, the 461 has 2.5 tanks consumed and this 460 is run in proper. Take that for what its worth.

 

[mweba]

I like the intake port direction and shape.

It is short and steep. Looking through the intake, the charge runs directly into the deflector/stuffer.

 

[Trx250r180]

is there gonna be any grinding pics ?

 

[mweba]

is there gonna be any grinding pics ?

Maybe :msp_biggrin:

Not until tomorrow though.

 

[mweba]

Video comparing the two.

[video=youtube_share;D1vFJeZXOHs]http://youtu.be/D1vFJeZXOHs[/video]

 

[Eccentric]

More like the shakiest gun in the west.


If we've met, you understand......

[video=youtube;Mzcgyk62cHU]http://www.youtube.com/watch?v=Mzcgyk62cHU[/video]

 

[Eccentric]

[video=youtube;fMfBk_k_79g]http://www.youtube.com/watch?feature=player_detailpage&v=fMfBk_k_79g[/video]