Jordan3605
ArboristSite Operative
Need some parts for a Husqvarna 340
Top Cover
Side Cover
Air Filter
Sprocket
Bar & Chain??
Thanks
Top Cover
Side Cover
Air Filter
Sprocket
Bar & Chain??
Thanks
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
nmurph
ArboristSite.com Sponsor
- Joined
- Nov 26, 2007
- Messages
- 16,162
- Reaction score
- 7,167
Is the filter a twist and click or a snap in (wire retainer?)
I have some clutch covers
I have plenty of rims (.325)
I have used .325/.058 B/C
little possum
Crash and Burn
I am on the hunt for a 064 gas tank and a recoil. Maybe a few other small parts after the tear down
dougs
ArboristSite Lurker
I'm still looking for a burnt up stihl 009. Need carb, and a few other parts. Anyone have one that they forgot to put the oil in?
Sent from my DROID RAZR using Tapatalk
Sent from my DROID RAZR using Tapatalk
May be able to help ya , SLACKER ! LOL
PM me I'm sure I have what you need.
If I were you I'd take this opertunity to put an AM wide discharge on the ms460. They are only $20-$30... eBay, weedeaterman.com, or Northwoodsaw should have them!
35.00 shipped is the cheapest I found them on flea bay.
Im on the lookout for a 28in bar and chain for a husqvarna 576xp. I have some paypal funds to send, sorry no parts at the moment...
Scott, you stihl needing this? I may have one. I'll wait to hear back from ya before I go lookin.... it's colder than a witches tata where it may be.
Nathan.. ya lost me on this one. Whatcha needing?
Looking for an 084 chain brake handle.....NLA from the dealer! Also interested in some other parts for it if you have anything.
I have lots to stuff to trade and get rid of guys. Looking for 385/390xp parts
Poulan 245 chainsaw, Craftsman 3.3; (poulan clone) dealer tag says needs new carb, looks like they did the fuel line and such already. Owner didn't want to put the money into it. Couple complete 023/025 saws.
Lots of 021/023/025 (plus other variants), husky top covers, husky 340/345/350 stuff, 031/032, 045/056, 066 cranks and crankcases. I need/want to downsize the parts pile.
I have lots to stuff to trade and get rid of guys. Looking for 385/390xp parts
Poulan 245 chainsaw, Craftsman 3.3; (poulan clone) dealer tag says needs new carb, looks like they did the fuel line and such already. Owner didn't want to put the money into it. Couple complete 023/025 saws.
Lots of 021/023/025 (plus other variants), husky top covers, husky 340/345/350 stuff, 031/032, 045/056, 066 cranks and crankcases. I need/want to downsize the parts pile.
IIRC I read a post on AS that the brake handle from a 066 will work
Wagnerwerks
The underdog..
I picked up a few echos I'm gonna part out. I have a 3900 with a good motor. Shop said it was fried, but it was so full of slimed sawdust it was hard to pull over..lol. I also picked up a 4600 with a fried top end.
I also have :
new old stock poulan 4200-8500 muffler with no front cover. Also a new bucking spike for this saw.
Stihl 039, 041 parts
Jonsered 535 saw that runs and could use rings
Echo/john deere 350 parts
Gobs of plastic poulans
Gobs of husky 50 parts.... No plastic.
Tons of 3400 poulan parts.
I'm looking for a nice 46mm 028super top end or just a cylinder (last ditch effort before I buy aftermarket) and a muffler with bolts.
And an echo 315 starter.
I also have :
new old stock poulan 4200-8500 muffler with no front cover. Also a new bucking spike for this saw.
Stihl 039, 041 parts
Jonsered 535 saw that runs and could use rings
Echo/john deere 350 parts
Gobs of plastic poulans
Gobs of husky 50 parts.... No plastic.
Tons of 3400 poulan parts.
I'm looking for a nice 46mm 028super top end or just a cylinder (last ditch effort before I buy aftermarket) and a muffler with bolts.
And an echo 315 starter.
nmurph
ArboristSite.com Sponsor
- Joined
- Nov 26, 2007
- Messages
- 16,162
- Reaction score
- 7,167
Kris, I can use the 288 spikes.
Wagnerwerks
The underdog..
Sounds good... I'll keep adding to the pile till it evens out. . 
One quick effort to find a 088 crank before I just part it out. Was replacing clutch springs on my personal 088 and found some bearing play. Tore it down to find that the crank just slides into the PTO bearing with little or no effort. .
Tons to trade and $.
. Tons to trade and $.
sld961
Addicted to ArboristSite
Bump
ramzilla
ArboristSite Guru
I need another dual port muffler or just the front cover for a 044/046. I got cash and parts to trade.
They make aftermarket covers for that style clutch cover now. Only used ones I have are beat.
Similar threads
