Looking for a ms441 muffler....
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
discounthunter
Addicted to ArboristSite
looking for a used but still usable 20" stihl mount 3003 3/8, .050 bar.72dl.thanks ,dave.
Wagnerwerks
The underdog..
I probably do.... I'll have to check which one that model uses.Anybody have an oil pump for a 46cc Craftsman. I started this project 2 years ago... somehow the pump is MIA.
I have a new 6 tooth 3/8 P spur sprocket I bought for an 020. Turns out the oil pump only fits an 1/4" 8 tooth spur sprocket. Any body have a new or like new 1/4" 8 tooth that fits the older 020"s ?
I have lots of parts I could trade, mostly Stihl, some Husky, McCulloch, this and that,sprockets, chains etc.
I have lots of parts I could trade, mostly Stihl, some Husky, McCulloch, this and that,sprockets, chains etc.
Wagnerwerks
The underdog..
Is that the same as the 015?
Scored piston missing coil, looking for dolmar/Makita540 piston and or cylinder and brake handle
sefh3
Addicted to ArboristSite
Anyone have a few .325 16 or 18 Stihl bars? I could use 3 or 4. Don't need to look pretty.
“I have a new 6 tooth 3/8 P spur sprocket I bought for an 020. Turns out the oil pump only fits an 1/4" 8 tooth spur sprocket. Any body have a new or like new 1/4" 8 tooth that fits the older 020"s ?
I have lots of parts I could trade, mostly Stihl, some Husky, McCulloch, this and that,sprockets, chains etc.
Is that the same as the 015?"
I think so. I might have an 015 I can check on.
I have lots of parts I could trade, mostly Stihl, some Husky, McCulloch, this and that,sprockets, chains etc.
Is that the same as the 015?"
I think so. I might have an 015 I can check on.
Jimmy in NC
Addicted to ArboristSite
I'll dig this evening....I may have one.
machinisttx
Addicted to ArboristSite
Anyone happen to have a good Echo CS-6700 jug and top end plastics laying around? Might have parts to trade or $$$
Thanks
I dug out an 015 powerhead of my collection. I don't remember trouble shooting it when I got it so I flushed out the fuel tank, primed it and it started and run well on its own about a minute + the oiler works. Its ready for a sprocket also if I do not determine a major problem when I further test it.
Jimmy in NC
Addicted to ArboristSite
Didn't get out there last night.....will in a few minutes though.Thanks
I dug out an 015 powerhead of my collection. I don't remember trouble shooting it when I got it so I flushed out the fuel tank, primed it and it started and run well on its own about a minute + the oiler works. Its ready for a sprocket also if I do not determine a major problem when I further test it.
Not chainsaw related but my neighbor dropped off a couple of things, first a single line primer assembly for a tecumseh tc 200 tiller and a stator plate for a snapper rer with a tecumseh 10hp engine
blueberrymuzik
Lesser Known AS Member
Anyone have a flywheel for a MS250 Easy Start? I believe the p/n is 1123 400 1207. I have parts and green stamps to trade.
Jimmy in NC
Addicted to ArboristSite
One I have is 1/4". Let me knock it apart this evening and send you some pictures in a PM.Thanks
I dug out an 015 powerhead of my collection. I don't remember trouble shooting it when I got it so I flushed out the fuel tank, primed it and it started and run well on its own about a minute + the oiler works. Its ready for a sprocket also if I do not determine a major problem when I further test it.
kc4sfe
ArboristSite Operative
I'm looking for a crankcase for a Stihl 076 that has the oiler intact. I have a Stihl MS362 crankcase/FW/clutch/coil with questionable bearings, poulan/craftsman 2150 parts, and a few other odds and ends for trade.
KenJax Tree
Terraphobic
I'm looking to trade a brand new 3/8 .050 16" Oregon Pro-Lite Husky large mount for a new 3/8 .050 16" Pro-Lite Husky small mount.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Similar threads
