sefh3
Addicted to ArboristSite
I no it's not a chainsaw but I picked up a Ryobi 410R rototiller. Any one have a motor for one of these? Pretty good shape but the piston and cylinder is toast. I have parts to trade.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
He is going to get a goober of white lithium grease around the gears when he goes back together.
rednecksawman
ArboristSite Operative
im still looking I got the flywheel I stuck that stuff someplace .
tomdcoker
Addicted to ArboristSite
Thanks. I know how that goes. I have parts that I know are in the shop somewhere, but finding them is impossible. Tom
rednecksawman
ArboristSite Operative
yea find stuff like that all the time when I DONT need them lol
I need a Jonsered 2094, 2095, Husqvarna 394, or 395 top end.
Parts or paper to trade.
Bryan
Parts or paper to trade.
Bryan
tomdcoker
Addicted to ArboristSite
rednecksawman
ArboristSite Operative
Tom i have looked high and low for that coil. I have the flywheel if you need it and the muffler and gas tank
i
tomdcoker
Addicted to ArboristSite
I know how that is. Like I told you before I have promised someone parts that i knew I had, but could not find them. I appreciate that you looked for it, but I only need the coil. Please just remember me if you run across it. Thanks for the effort. Tom
bump!
Flat47
ArboristSite Guru
- Joined
- Jan 6, 2014
- Messages
- 563
- Reaction score
- 301
Looking for Husky 372 XTorq hi-top air filter cover and air filter mount for the screw-down filter.
Bolt holes are different on the Xtorq. I think the bolt holes on the filter mount are nearly horizontal on the XTorq- already bought the the wrong one off an XP.
Bolt holes are different on the Xtorq. I think the bolt holes on the filter mount are nearly horizontal on the XTorq- already bought the the wrong one off an XP.
before i go the ebay route anybone have any of the following:
036 recoil
026 carb, 2 x air filter, cover
260 handle
not urgent but looking for an ms660 with a bad engine
have 021 engine assembly w/coil perfect shape, 021 handle, ht131 engine, an unknown stihl weedwacker engine, or cash also have a craftsman 3.7/18" with case, extra chain, and tools i can trade, needs the handle bar buffer and carb kit
036 recoil
026 carb, 2 x air filter, cover
260 handle
not urgent but looking for an ms660 with a bad engine
have 021 engine assembly w/coil perfect shape, 021 handle, ht131 engine, an unknown stihl weedwacker engine, or cash also have a craftsman 3.7/18" with case, extra chain, and tools i can trade, needs the handle bar buffer and carb kit
Mantis coil. I have one that was scored. No clue if coil was good or bad, came in apart. I will see if still on the shelf. Been there a couple years now. So red wire coil is the one needed?
Guess I need to look for that poulan muffler cover for a guy too .
Guess I need to look for that poulan muffler cover for a guy too .
Mantis coil. I have one that was scored. No clue if coil was good or bad, came in apart. I will see if still on the shelf. Been there a couple years now. So red wire coil is the one needed?
Guess I need to look for that poulan muffler cover for a guy too .
Ran out during commercial break during BB game. Mantis coil I have is grey with black wire. Oh well.
Still forgot to look for poulan muffler cover.
MS460WOODCHUCK
Addicted to ArboristSite
Hey guys I'm needing the little screw that holds on the fuel tank guard for a 044. I do not have another around to compare or I would just get one at the local hardware. I would hate to run the wrong screw in and ruin the plastic threads of the handle. PM me if you can help me out.
cat-face timber
Knot Bumper
Anybody want to trade a left bucking spur for the right one?
I need the one from the clutch cover if anybody has one.
Husky 288.
I need the one from the clutch cover if anybody has one.
Husky 288.
Looking for a decent 372xp muffler. Rust is ok, just no dents. Send me a pm.
Thanks!
Thanks!
Guido Salvage
Supreme Saw Whoreder
Terry Landrum is a Redmax dealer, can he help?
Similar threads
