066/MS 660 port #'s. Please share your stock #'s

[Trx250r180]

Sounds like harvestor chain

 

[Deets066]

Sounds like harvestor chain

Yup, I used it to harvest some tree's lives

 

[Moparmyway]

Sounds like harvestor chain

.404 RS comes with .045 from the factory

Ok, got a minute today to run the newly improved 066. I will say that I'm definately happy with it and maybe I can finally quit messin with it and run it!
I ran it with a 24 and 8 pin with rakers set at -.050, it's definately a beast. I'll get video tomorrow with a 36" bar.

Whats the compression and final numbers at again ?

Finally. Somebody else who enjoys a saw that pulls itself through the wood. I thought I was the only one at .040

I have ran .040 lots of times on .375. The cutters dont last as long as with .030 though

At -.050 you can stall any saw, regaurdless of displacement. But if you let it cut, you can chew up some wood

.050 aint for boys ....................

 

[drf255]

.404 RS comes with .045 from the factory

Explains alot to me.

I was able to bog my Masterminded 066 with a 28" .404 buried in Maple. Now I know why.

 

[Deets066]

I'll get another compression reading today,
Ex. 101
Trans. 118
Intake. 77
Triple port muffler
Timing advanced
Maxflo
Carb shafts and butterflies ground down and tapered.

Next in line is drilling the jet in the carb

 

[Mastermind]

Does it feel stronger with the intake raised?

 

[Deets066]

Does it feel stronger with the intake raised?

From the few cuts I made with it, I'd say yes it does.
I'm getting ready to head to the shop and put it in some real wood though

 

[Mastermind]

More intake seems to make a faster saw, less intake makes a stronger saw. If that makes any sense.

 

[Deets066]

 

[Deets066]

This don't do the saw much justice, chain needs touched up

 

[Mastermind]

I just listen mostly. It's holding RPM real good in the cut with that big bar.

 

[big t double]

Glad your gettin all this portin stuff fingered out there deets....save me a ton on shipping cost...get a lathe yet?

 

[Mastermind]

You bastards are gonna put me outta bidness.

 

[Moparmyway]

I'll get another compression reading today,
Ex. 101
Trans. 118
Intake. 77
Triple port muffler
Timing advanced
Maxflo
Carb shafts and butterflies ground down and tapered.

Next in line is drilling the jet in the carb

Allmost the same numbers, except trans ........I am at 122
What RPM is she at WOT unloaded in the video ?
She sounds snappy, like mine !
Them 661r dogs look great !!!

 

[Moparmyway]

You bastards are gonna put me outta bidness.

Not in a million years Sir ......................
You and Big Mike are the reason why I did mine in the first place !!

 

[Deets066]

Allmost the same numbers, except trans ........I am at 122
What RPM is she at WOT unloaded in the video ?
She sounds snappy, like mine !

Compression 215 warm
Rpm 14,000 at two full turns out on the H

 

[Moparmyway]

2 turns ............
Want a .74 jet ?

 

[Deets066]

2 turns ............
Want a .74 jet ?

I think that would help

 

[Deets066]

I just listen mostly. It's holding RPM real good in the cut with that big bar.

Especially with the nose buried

 

[Mastermind]

Just drill that jet Deets. See what size micro bit fits it now, and go up two numbers.