Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I still lurk around here and there but I've been swamped at work and home for the last 2 months. I hope to get some time off around Christmas. I think I still owe you some parts ...

dd

nah... what goes around comes around! I've given and received plenty of help without keeping count the last few months... i think I'm finally at that point that I realize it will all be close to even in the end!

On a personal note I just got the garage organized again for the 3rd time this year... Got some projects awaiting me... anyone have any of the following. Cash and parts to trade for any of the following...

655 poulan AF
120si or 6800 dolmar Piston and/or cylinder
1121 stuff.... I'm always collecting 024/026 stuff...
009-012 P&C's... I'm going to do a holiday build off on about 6 of these and give to people in need w/ low $$$ flow...
might need 021/025 P&C... not sure yet...

I have a lil' poulan 2150 that anyone can have for parts (u pay shipping). I think it's just astetic fixes and fuel system...
I have a few carbs to post but need to get a list... maybe tomorrow..??
 
nah... what goes around comes around! I've given and received plenty of help without keeping count the last few months... i think I'm finally at that point that I realize it will all be close to even in the end!

On a personal note I just got the garage organized again for the 3rd time this year... Got some projects awaiting me... anyone have any of the following. Cash and parts to trade for any of the following...

655 poulan AF
120si or 6800 dolmar Piston and/or cylinder
1121 stuff.... I'm always collecting 024/026 stuff...
009-012 P&C's... I'm going to do a holiday build off on about 6 of these and give to people in need w/ low $$$ flow...
might need 021/025 P&C... not sure yet...

I have a lil' poulan 2150 that anyone can have for parts (u pay shipping). I think it's just astetic fixes and fuel system...
I have a few carbs to post but need to get a list... maybe tomorrow..??

Dennis Cahoon has a couple 023 p/c sets for sale, in the classifieds.
 
Need some some things. A walbro wt22b carb for an 024. Pistons for an 024 (42mm) and a piston for an 026 (44mm). Got some to trade, and cash.
 
I need a clutch, bearing , and drum for a 137...I'm guessing a WT might be the same saw???

A husky 137? Ya, lot of parts out there for those, it crosses with a ton of other makes/models

Here is randy duncans list off of ebay.

Husqvarna Clutch Fits 36 41 136 141 137 142 235 E 240 McCulloch Partner Jonsered | eBay

I have one, first new saw I ever bought, still runs like new. I treated it like it was a 50 cc saw from day one, cut tons and tons of wood with it, from saplings to once a downed 20" oak. All I have changed is clutch/spur sprocket and bearing, and some bars and chains, and swapped in a new oiler once. The oilers would actually last a long time if they get taken off and cleaned, builds up crud back behind it, then the plastic gears get worn out. I didnt know that until I got a new one and took the old one off.
 
Looking for a good piston and ring for a husqvarna 142.

Any thoughts on the aftermarket ones from Northwood saw?

I'm fixing it for a friend and was able to acid clean the cylinder pretty good.
 
Looking for a good piston and ring for a husqvarna 142.

Any thoughts on the aftermarket ones from Northwood saw?

I'm fixing it for a friend and was able to acid clean the cylinder pretty good.

I think I have what your looking for, let me check in a little bit. If my wife sees me going near my shop, she'll chop my ballz off right now.
 
Looking for a large (32" - 42") bar (plus chain?) .063 for a Homelite 1130G. Hard nose or roller naose preferred. I have various parts and ca$h to trade. Please PM me if you can help out. Thanks!
 
Looking for JD 50 rewind, or if you have an Echo 452 its the same. Cash, chains, bars, a few parts.

Taken care of. Thanks JJ!
 
Last edited:
Looking for JD 50 rewind, or if you have an Echo 452 its the same. Cash, chains, bars, a few parts.

Got it, the Echo version. Where does it go?

Anyone have a Stihl 050AV parts saw. Need at least the rear lower handle casting and a muffler. Have stuff to trade.

Muffler, yes. Rear lower handle casting, probably not.
 
clutch cover

I have a stock 460 clutch cover nearly brand new. Willing to trade for a dual port exhaust cover for the same type saw.
 
Back
Top